BS EN 1329-1:2020 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U). Specifications for pipes, fittings and the system

BS EN 1329-1:2020

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U). Specifications for pipes, fittings and the system

Status : Current   Published : December 2020

Format
PDF

Format
HARDCOPY



This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) piping systems intended for soil and waste discharge applications (low and high temperature):

  1. inside buildings (application area code “B”);

  2. for both inside buildings and buried in ground within the building structure (application area code “BD”).

NOTE 1

The intended use is reflected in the marking of products by “B”e e e or “BD”.

NOTE 2

Application "B" covers uses above ground inside the building, or outside buildings fixed onto the wall.

NOTE 3

Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 1453-1 [ 1].

NOTE 4

For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm.

NOTE 5

EN 476 [ 2] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements.

This document is also applicable to PVC-U pipes, fittings and the system intended for the following purposes:

  1. ventilating part of the pipework in association with discharge applications;

  2. rainwater pipework within the building structure.

This document also specifies the test parameters for the test methods that are referred to.

This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.

NOTE 6

It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

NOTE 7

Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 26.




Standard NumberBS EN 1329-1:2020
TitlePlastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U). Specifications for pipes, fittings and the system
StatusCurrent
Publication Date11 December 2020
Normative References(Required to achieve compliance to this standard)EN ISO 1043-1, EN ISO 13259, EN ISO 13254, EN ISO 3127, EN 681-1, ISO 18373-1, EN ISO 472, EN ISO 1158, EN 1401-1, EN 681-2, EN ISO 6259-1, EN ISO 11173, EN ISO 2507-1, EN ISO 9852, EN 14814, EN ISO 1183-1, EN ISO 3451-5, EN ISO 580, ISO 6259-2, EN 14680, EN ISO 2505, EN ISO 3126, EN ISO 13255, EN ISO 1167-2:2006, EN ISO 13257:2018, EN ISO 1167-1:2006
Informative References(Provided for Information)EN 1453-1, ISO 265-1, EN ISO 11925-2, TS 1329-2, EN 16000, EN 13823, EN ISO 9001, EN 476, EN 13501-1, EN 15346:2014, ISO 4065:2018
ReplacesBS EN 1329-1:2014+A1:2018
International RelationshipsEN 1329-1:2020
Amended ByCorrigendum, April 2021
DescriptorsRecycling, Waste-water drainage, Diameter, Dimensions, Water supply and waste systems (buildings), Impact strength, Marking, Pipe fittings, Performance, Physical properties of materials, Thickness, Polyvinyl chloride, Spigot-and-socket joints, Mechanical properties of materials, Length, Pipework systems, Pipes, Drainage, Plastics, Size, Sealing rings, Unplasticized polyvinyl chloride
ICS23.040.01
Title in FrenchSystèmes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur de la structure des bâtiments. Poly(chlorure de vinyle) non plastifié (PVC-U) Spécifications pour tubes, raccords et le système
Title in GermanKunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebäudestruktur. Weichmacherfreies Polyvinylchlorid (PVC-U) Anforderungen an Rohre, Formstücke und das Rohrleitungssystem
CommitteePRI/88/1
ISBN978 0 539 16549 4
PublisherBSI
FormatA4
DeliveryYes
Pages52
File Size1.565 MB
Price£260.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Develop a PAS

Develop a fast-track standardization document in 9-12 months


Worldwide Standards
We can source any standard from anywhere in the world


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version