20/30420217 DC - BS EN 1566-1. Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Chlorinated poly(vinyl chloride) (PVC-C). Part 1. Requirements for pipes, fittings and the system

20/30420217 DC

BS EN 1566-1. Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Chlorinated poly(vinyl chloride) (PVC-C). Part 1. Requirements for pipes, fittings and the system

Status : Current, Draft for public comment   Published : July 2020

Format
PDF

Format
HARDCOPY



This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of chlorinated poly(vinyl chloride) (PVC-C) piping systems intended for soil and waste discharge (low and high temperature):

  • inside buildings (application area code “B”);

  • for both inside buildings and buried in ground within the building structure (application area code “BD”).

NOTE 1

The intended use is reflected in the marking of products by “B” or “BD”.

NOTE 2

Application “B” covers uses above ground inside buildings, or outside buildings fixed onto the wall.

NOTE 3

Pipes and fittings of the pipe series S 25 are intended to be used for application area “B” only.

NOTE 4

For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm.

NOTE 5

EN 476 [1] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements.

This document is applicable to PVC-C pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following purposes:

  • ventilating part of the pipework in association with discharge applications;

  • rainwater pipework within the building structure.

It also specifies the test parameters for the test methods that are referred to.

This document covers a range of nominal sizes, a range of pipe series and gives recommendations concerning colours.

NOTE 6

It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices codes.

NOTE 7

Pipes, fitting and other components conforming to any of the plastics product standards listed Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.




Standard Number20/30420217 DC
TitleBS EN 1566-1. Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Chlorinated poly(vinyl chloride) (PVC-C). Part 1. Requirements for pipes, fittings and the system
StatusCurrent, Draft for public comment
Publication Date20 July 2020
Normative References(Required to achieve compliance to this standard)EN ISO 2507-2, EN 681-1, EN ISO 2507-1, EN ISO 13259:2018, EN ISO 13255, ISO 8361-1, EN ISO 13254, EN ISO 1043-1, EN ISO 11173, EN 14814, EN 681-2, EN ISO 1167-2:2006, EN ISO 2505:2005, EN 14680, EN ISO 3127, EN ISO 1167-1:2006, EN ISO 472, EN ISO 580:2005, EN ISO 9969, EN ISO 3126, EN ISO 13257:2018
Informative References(Provided for Information)EN 13823, EN ISO 11925-2, EN ISO 13967, CEN/TS 1566-2, EN 476, EN 13501-1, EN 16000, EN 1401-1, ISO 265-1, ISO 4065:2018
International RelationshipsprEN 1566-1
Draft Expiry Date09 September 2020
DescriptorsSealing rings, Polyvinyl chloride, Length, Mechanical properties of materials, Testing conditions, Pipework systems, Plastics, Thickness, Diameter, Performance, Polyvinylidene chloride, Drainage, Size, Pipes, Water supply and waste systems (buildings), Pipe fittings, Dimensions, Waste-water drainage, Marking, Physical properties of materials, Spigot-and-socket joints
ICS23.040.01
91.140.80
Title in FrenchSystèmes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur de la structure des bâtiments - Poly(chlorure de vinyle) chloré (PVC-C) Partie 1: spécifications pour tubes, raccords ainsi que pour le système
Title in GermanKunststoff- Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebäudestruktur - Chloriertes Polyvinylchlorid (PVC-C) Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem
CommitteePRI/88/1
PublisherBSI
FormatA4
DeliveryYes
Pages41
File Size671 KB
NotesWarning: this draft is not current beyond its expiry date for comments.
Price£20.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Worldwide Standards
We can source any standard from anywhere in the world


BSOL

Access, view and download standards with multiple user access, across multiple sites with BSOL


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version