BS EN 1519-1:2019 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE). Requirements for pipes, fittings and the system

BS EN 1519-1:2019

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE). Requirements for pipes, fittings and the system

Status : Current   Published : May 2019

Format
PDF

Format
HARDCOPY



This document specifies the requirements for solid-wall polyethylene (PE) pipes with smooth internal and external surfaces extruded from the same compound/formulation throughout the wall, fittings and the system for: - soil and waste discharge applications (low and high temperature) inside buildings (application area code "B"); - soil and waste discharge applications (low and high temperature) for both inside buildings and buried in the ground within the building structure (application area code "BD"). NOTE 1 The intended use is reflected in the marking of products by "B" or "BD". NOTE 2 For use buried in the ground within the building structure are intended only those components marked with "BD", with a nominal ring stiffness of at least SN4 for dimensions equal to or greater than 75 mm. This document is also applicable to PE pipes and fittings and the system intended for the following purposes: - ventilating part of the pipework in association with discharge applications; - rainwater pipework within the building structure. It also specifies the test parameters for the test methods referred to in this standard. This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes, e.g. CEN/TR 13801 [1]. NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, if applicable. It applies to pipes and fittings, marked with “B”, which are intended to be used inside buildings and outside buildings fixed onto the wall. It applies to pipes and fittings, marked with “BD”, which are intended to be used for both inside buildings and buried in the ground within the building structure. This standard is applicable to PE pipes and fittings of the following types: - plain-ended; - with integral elastomeric ring seal socket; - for butt fusion joints; - for electrofusion joints; - for mechanical joints where the fittings can be manufactured by injection-moulding or can be fabricated from pipes and/or mouldings. NOTE 5 EN 476[2] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements. NOTE 6 For information about the chemical resistance of PE, guidance is given in ISO/TR 10358[3] and for rubber materials in ISO/TR 7620[4].




Standard NumberBS EN 1519-1:2019
TitlePlastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE). Requirements for pipes, fittings and the system
StatusCurrent
Publication Date02 May 2019
Normative References(Required to achieve compliance to this standard)EN ISO 13257:2018, EN 681-1, ISO 4065, EN 12099, EN ISO 1167-2, EN ISO 1043-1, EN ISO 1133-1, EN ISO 3126, EN ISO 1167-1, EN ISO 13255, EN ISO 580, EN 681-2, EN ISO 472, EN ISO 9969, EN ISO 13259, EN ISO 13254, EN ISO 11357-6, EN ISO 3451-1, EN ISO 2505, EN ISO 13264, EN ISO 1183-2
Informative References(Provided for Information)TR 7620, EN 12201-2, EN 12666-1, EN ISO 13967, EN 476, EN ISO 9001, TR 10358, EN 12201-3, EN 1555-3, TR 13801, ISO 265-1, EN 1555-2
ReplacesBS EN 1519-1:2000
International RelationshipsEN 1519-1:2019
Amended ByCorrigendum, December 2019
DescriptorsSealing rings, Water supply and waste systems (buildings), Performance, Length, Pipework systems, Diameter, Testing conditions, Pipes, Drainage, Pipe fittings, Dimensions, Size, Physical properties of materials, Plastics, Waste-water drainage, Spigot-and-socket joints, Marking, Thickness, Polyethylene
ICS23.040.01
23.040.20
83.140.30
91.140.80
Title in FrenchSystèmes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur de la structure des bâtiments. Polyéthylène (PE) Exigences pour tubes, raccords et le système
Title in GermanKunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebäudestruktur. Polyethylen (PE) Anforderungen an Rohre, Formstücke und das Rohrleitungssystem
CommitteePRI/88/1
ISBN978 0 539 11999 2
PublisherBSI
FormatA4
DeliveryYes
Pages42
File Size2.783 MB
Price£214.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Collaborate, Innovate, Accelerate.


BSOL

The faster, easier way to work with standards


Worldwide Standards
We can source any standard from anywhere in the world