19/30395450 DC - BS EN 1329-1. Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U). Part 1. Specifications for pipes, fittings and the systems

19/30395450 DC

BS EN 1329-1. Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U). Part 1. Specifications for pipes, fittings and the systems

Status : Draft for public comment, Current   Published : August 2019

Format
PDF

Format
HARDCOPY



This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) piping systems intended for soil and waste discharge applications (low and high temperature): - inside buildings (application area code "B"); - for both inside buildings and buried in ground within the building structure (application area code "BD"). NOTE 1 The intended use is reflected in the marking of products by "B" or "BD". NOTE 2 Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 1453-1 [1]. NOTE 3 For use buried in ground within the building structure are intended only those components (marked with "BD") with nominal outside diameters equal to or greater than 75 mm. NOTE 4 EN 476 [2] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements. This document is also applicable to PVC-U pipes, fittings and the system intended for the following purposes: - ventilating part of the pipework in association with discharge applications; - rainwater pipework within the building structure. This document also specifies the test parameters for the test method that are referred to. This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours. NOTE 5 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. For external above ground application additional requirements depending on the climate should be agreed between the manufacturer and the user. NOTE 6 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 25.




Standard Number19/30395450 DC
TitleBS EN 1329-1. Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U). Part 1. Specifications for pipes, fittings and the systems
StatusDraft for public comment, Current
Publication Date19 August 2019
Normative References(Required to achieve compliance to this standard)EN ISO 3126, EN 1401-1, EN ISO 11173, EN ISO 1167-1:2006, EN ISO 3127, EN ISO 13255, EN ISO 1167-2:2006, EN ISO 2505, EN ISO 472, EN ISO 6259-1, EN ISO 13254, EN 681-2, EN ISO 9852, EN 14680, EN ISO 1183-1, ISO 6259-2, ISO 18373-1, EN ISO 1043-1, EN 681-1, EN ISO 13259, EN ISO 13257:2018, EN 14814, EN ISO 2507-1, EN ISO 3451-5, EN 1905, EN ISO 580
Informative References(Provided for Information)EN 15346:2014, CEN/TS 1329-2, ISO 265-1, EN 476, EN 1453 (all parts), EN ISO 9001
International RelationshipsFprEN 1329-1
Draft Expiry Date14 October 2019
DescriptorsThickness, Pipe fittings, Length, Marking, Diameter, Polyvinyl chloride, Pipework systems, Sealing rings, Performance, Drainage, Physical properties of materials, Waste-water drainage, Size, Water supply and waste systems (buildings), Impact strength, Mechanical properties of materials, Plastics, Dimensions, Pipes, Recycling, Unplasticized polyvinyl chloride, Spigot-and-socket joints
ICS23.040.20
91.140.80
Title in FrenchSystèmes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur de la structure des bâtiments - Poly(chlorure de vinyle) non plastifié (PVC-U) Partie 1:Spécifications pour tubes, raccords et le système
Title in GermanKunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebäudestruktur - Weichmacherfreies Polyvinylchlorid (PVC-U) Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem
CommitteePRI/88/1
PublisherBSI
FormatA4
DeliveryYes
Pages49
File Size704 KB
NotesWarning: this draft is not current beyond its expiry date for comments.
Price£20.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Worldwide Standards
We can source any standard from anywhere in the world


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version


Develop a PAS

Develop a fast-track standardization document in 9-12 months