19/30391758 DC - BS EN ISO 23856. Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage. Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin

Find Similar Items

This product falls into the following categories.

You may find similar items within these categories by selecting from the choices below:

19/30391758 DC

BS EN ISO 23856. Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage. Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin

Status : Current, Draft for public comment   Published : June 2019

Format
PDF

Format
HARDCOPY



This document specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of water supply, drainage and sewerage with or without pressure. Types of water supply include, but are not limited to, raw water, irrigation, cooling water, potable water, salt water, sea water, penstocks in power plants, processing plants and other water-based applications. This document is applicable to GRP UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in direct buried installations.

NOTE 1

For the purpose of this document, the term polyester resin (UP) also includes vinyl-ester resins (VE).

NOTE 2

Piping systems conforming to this document can also be used for non-buried applications, provided the influence of the environment and the supports are considered in the design of the pipes, fittings and joints.

NOTE 3

This document can also apply for other installations, such as slip-lining rehabilitation of existing pipes.

NOTE 4

This document is also referenced in ISO 25780, which specifies requirements for GRP-pipes used for jacking installation.

The requirements for the hydrostatic pressure design of pipes referring to this document meet the requirements of ISO/TS 20656-1 and the general principle for the reliability of structures detailed in ISO 2394 and in EN 1990. These International Standards provide procedures for the harmonization of design practices and address the probability of failure, as well as possible consequences of failures. The design practices are based on a partial safety factor concept, as well as on risk management engineering.

This document is applicable to pipes, fittings and their joints of nominal sizes from DN 50 to DN 4000 which are intended to be used for the conveyance of water at temperatures up to 50 °C, with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together. Clause 4 specifies the general aspects of GRP UP piping systems intended to be used in the field of drainage or sewerage with or without pressure.

Clause 5 specifies the characteristics of pipes made from GRP UP with or without aggregates and/or fillers. The pipes may have a thermoplastics or thermosetting resin liner. Clause 5 also specifies the test parameters for the test methods referred to in this document.

Clause 6 specifies the characteristics of fittings made from GRP UP, with or without a thermoplastics or thermosetting resin liner, intended to be used in the field of drainage and sewerage. Clause 6 specifies the dimensional and performance requirements for bends, branches, reducers, saddles and flanged adaptors. Clause 6 covers requirements to prove the structural design of fittings. It is applicable to fittings made using any of the following techniques:

  • fabrication from straight pipes;

  • moulding by

    1. filament winding,

    2. tape winding,

    3. contact moulding, and

    4. hot or cold compression moulding.

Clause 7 is applicable to the joints to be used in GRP UP piping systems to be used for the conveyance of surface water and sewerage, both buried and non-buried. It covers requirements to prove the design of the joint. Clause 7 specifies type test performance requirements for the following joints as a function of the declared nominal pressure rating of the pipeline or system:

  1. socket-and-spigot (including double-socket) joints or mechanical joints;

  2. locked socket-and-spigot joints;

  3. cemented or wrapped joints;

  4. bolted flange joints.




Standard Number19/30391758 DC
TitleBS EN ISO 23856. Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage. Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
StatusCurrent, Draft for public comment
Publication Date18 June 2019
Cross ReferencesISO 10471, CEN/TS 14632, ISO 527-5, ISO 18851, ISO 8533, ISO 10952, ISO 2531, ISO 7685, ISO 10466, ISO 10468, ISO 8483, ISO 7509, ISO 8639, ISO 11922-1, ISO 1452-3, ISO 4633, ISO 527-4, ISO 4200, ISO 161-1, ISO/TS 20656-1, ISO 7432, ISO 3126, ISO 10928:2016, ISO 8521:2009, ISO 75-2:2013, ISO 2394:2015, ISO 8513:2016, AWWA C950, EN 681-2, ISO 7511, AWWA M45, ISO 2078, ISO 25780, EN 681-1, ISO/IEC 17025, JIS A 5350, EN 1990
International RelationshipsISO/DIS 23856
Draft Expiry Date06 August 2019
ICS23.040.20
91.140.80
93.030
Title in FrenchSystèmes de canalisation en matières plastiques pour les branchements et les collecteurs d'assainissement avec ou sans pression -- Systèmes en plastiques thermodurcissables renforcés de verre (PRV) à base de résine de polyester non saturé (UP)
CommitteePRI/88/2
PublisherBSI
FormatA4
DeliveryYes
Pages68
File Size1.042 MB
NotesWarning: this draft is not current beyond its expiry date for comments.
Price£20.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


27 November

Organizational Resilience Annual Conference 2019


Worldwide Standards
We can source any standard from anywhere in the world


BSOL

The faster, easier way to work with standards