ASTM C1648 - 12(2018) - Standard Guide for Choosing a Method for Determining the Index of Refraction and Dispersion of Glass

ASTM C1648 - 12(2018)

Standard Guide for Choosing a Method for Determining the Index of Refraction and Dispersion of Glass

Status : Current   Published : August 2018

Format
PDF

Format
HARDCOPY



1.1 This guide identifies and describes seven test methods for measuring the index of refraction of glass, with comments relevant to their uses such that an appropriate choice of method can be made. Four additional methods are mentioned by name, and brief descriptive information is given in Annex A1. The choice of a test method will depend upon the accuracy required, the nature of the test specimen that can be provided, the instrumentation available, and (perhaps) the time required for, or the cost of, the analysis. Refractive index is a function of the wavelength of light; therefore, its measurement is made with narrow-bandwidth light. Dispersion is the physical phenomenon of the variation of refractive index with wavelength. The nature of the test-specimen refers to its size, form, and quality of finish, as described in each of the methods herein. The test methods described are mostly for the visible range of wavelengths (approximately 400 to 780 μm); however, some methods can be extended to the ultraviolet and near infrared, using radiation detectors other than the human eye.

1.1.1 List of test methods included in this guide:

1.1.1.1 Becke line (method of central illumination),

1.1.1.2 Apparent depth of microscope focus (the method of the Duc de Chaulnes),

1.1.1.3 Critical Angle Refractometers (Abbe type and Pulfrich type),

1.1.1.4 Metricon 2 system,

1.1.1.5 Vee-block refractometers,

1.1.1.6 Prism spectrometer, and

1.1.1.7 Specular reflectance.

1.1.2 Test methods presented by name only (see Annex A1):

1.1.2.1 Immersion refractometers,

1.1.2.2 Interferometry,

1.1.2.3 Ellipsometry, and

1.1.2.4 Method of oblique illumination.

1.2  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.3  Warning—Refractive index liquids are used in several of the following test methods. Cleaning with organic liquid solvents also is specified. Degrees of hazard associated with the use of these materials vary with the chemical nature, volatility, and quantity used. See manufacturer's literature and general information on hazardous chemicals.

1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.




Standard NumberASTM C1648 - 12(2018)
TitleStandard Guide for Choosing a Method for Determining the Index of Refraction and Dispersion of Glass
StatusCurrent
Publication Date01 August 2018
Normative References(Required to achieve compliance to this standard)No other standards are normatively referenced
Informative References(Provided for Information)No other standards are informatively referenced
Descriptors Abbe-number, dispersion, glass, index of refraction, refractive index, refractometer
ICS81.040.30
PublisherASTM
FormatA4
DeliveryYes
Pages15
File Size310 KB
Price£45.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


BSOL

The faster, easier way to work with standards


Worldwide Standards
We can source any standard from anywhere in the world


Develop a PAS

Develop a fast-track standardization document in 9-12 months