ASTM C1396/C1396M - 17 - Standard Specification for Gypsum Board

Related Standards

ASTM C1396/C1396M - 17

Standard Specification for Gypsum Board

Status : Current   Published : July 2017

Format
PDF

Format
HARDCOPY



1.1 This specification covers the gypsum boards described in 1.1.1 –1.1.9.

Note 1:  Specifications C840, C841, C844 and C1280 contain application procedures for gypsum board.

1.1.1  Gypsum wallboard, designed for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration.

1.1.2  Predecorated gypsum board, designed for use as the finished surfacing for walls, ceilings, or partitions.

1.1.3  Gypsum backing board, coreboard, and shaftliner board, designed for use as a base in multilayer systems or as a gypsum stud or core in semisolid or solid gypsum board partitions, or in shaft wall assemblies.

Note 2:  The terms backing board, coreboard, and shaftliner board refer to different end uses. The term gypsum backing board, as used in this specification, shall include gypsum coreboard and gypsum shaftliner board unless otherwise stated.

1.1.4  Water-resistant gypsum backing board, designed primarily to be used as a base for the application of ceramic or plastic tile on walls or ceilings. This product is also suitable for decoration.

1.1.5  Exterior gypsum soffit board, designed for use on exterior soffits and carport ceilings that are completely protected from contact with liquid water.

1.1.6  Gypsum sheathing board, designed for use as sheathing on buildings.

1.1.7  Gypsum base for veneer plaster, designed for use as a base for the application of gypsum veneer plaster.

1.1.8  Gypsum lath, designed for use as a base for the application of gypsum plaster.

1.1.9  Gypsum ceiling board, designed for use on interior ceilings with framing spaced not more than 24 in. [610 mm] on center and that affords a surface suitable to receive water-based texture and other decoration. This product is also suitable for use on interior walls.

1.2 Specifications applicable to all gypsum boards are located in Section 1 –4 and 13 –15. Specifications applicable to specific gypsum boards are located in the following sections:

[This table has been removed.]



1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard

1.4  This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.




Standard NumberASTM C1396/C1396M - 17
TitleStandard Specification for Gypsum Board
StatusCurrent
Publication Date01 July 2017
Normative References(Required to achieve compliance to this standard)No other standards are normatively referenced
Informative References(Provided for Information)No other standards are informatively referenced
Descriptors Ceiling Coreboard Drywall Exterior gypsum soffit board Foil-backed Gypsum Gypsum backing board Gypsum base Gypsum board Gypsum ceiling board Gypsum coreboard Gypsum lath Gypsum sheathing Gypsum sheathing board Gypsum wallboard Laminated gypsum board Partitions Plaster Predecorated gypsum board Shaftliner Sheathing Type X Veneer base Veneer plaster Wall Wallboard Water-resistant gypsum board
ICS91.060.10
PublisherASTM
FormatA4
DeliveryYes
Pages8
File Size117 KB
Price£40.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


BSOL

The faster, easier way to work with standards


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version


Develop a PAS

Develop a fast-track standardization document in 9-12 months