BS EN 13914-1:2016 - Design, preparation and application of external rendering and internal plastering. External rendering

BS EN 13914-1:2016

Design, preparation and application of external rendering and internal plastering. External rendering

Status : Current   Published : March 2016

Format
PDF

Format
HARDCOPY



This European Standard specifies requirements and recommendations for the design, preparation and application of

  • renders based on cement, lime or other mineral binders, and/or combinations thereof, masonry cement and polymer modified binder based external renderings, in accordance with EN 998‑1 or site made renders;

  • renders based on organic binders in accordance with EN 15824

on all common types of backgrounds. It includes rendering on both new and old backgrounds and the maintenance and repair of existing work. This document gives guidance on the use of established site, factory and semi-finished factory made renders.

This document does not cover the following:

  1. the use and application of special renders for liquid retaining structures, e.g. coatings, and for backgrounds to cladding systems;

  2. the structural repair of concrete;

  3. the installation of external thermal insulation composite systems (ETICS);

  4. the specification and use of sealants used to seal joints for use with rendering;

  5. the use of gypsum based renders used externally, but their use may be permitted in some countries;

    Gypsum based products soften when subject to prolonged moist conditions. The use of such products externally will depend upon the climatic conditions where the render will be used and on the local building traditions. With the exception of some drier countries in southern Europe gypsum based renders are generally not recommended for external use and are therefore not included within the scope of this document. However, their use may be permitted and controlled locally. 1)

  6. renders on historical monuments or buildings in protected areas which may be regulated by national codes;

  7. the design and installation of flashings at windowsills and elsewhere.

Because of the many and varied materials and practices and different climatic conditions in Europe it is not possible for certain aspects of the standard to enter into sufficient detail to be fully usable to practitioners in each country. Appropriate guidance to complement, but not alter any basic European recommendations is given in documentation prepared by each country. Aspects of this European Standard whose basic recommendations may need to be complemented are indicated where they occur by a footnote referencing this clause.




Standard NumberBS EN 13914-1:2016
TitleDesign, preparation and application of external rendering and internal plastering. External rendering
StatusCurrent
Publication Date31 March 2016
Normative References(Required to achieve compliance to this standard)ISO 16120-2:2017, EN 12878:2014, EN ISO 14616 (ISO 14616:1997) AS, EN 1996-2:2006, ISO 1461:2009 Ed 3, EN 197-1:2011, EN 998-1:2010, EN 13496:2013, EN 10088-1:2014, EN 13658-2:2005, EN ISO 16120-2 (ISO 16120-2:2017) AS, EN 459-1:2015, EN 15824:2009, EN 13055-2:2004, EN 413-1:2011, EN 10346:2015, EN 1008:2002, EN 13139:2013, EN 934-3:2009+A1:2012
Informative References(Provided for Information)No other standards are informatively referenced
ReplacesBS EN 13914-1:2005
Amended ByCorrigendum, April 2017
DescriptorsWall coverings, Interior wall coverings, Lime, Finishes, Polymers, Reinforcing materials, Exterior wall coverings, Maintenance, Wall coatings, Cements, Walls, Design, Binding agents, Coating processes, Plastering, Masonry cement, Construction materials, Repair, Coatings, Surfaces, Render
ICS91.100.10
Title in FrenchConception, préparation et application des enduits extérieurs et intérieurs. Enduits extérieurs
Title in GermanPlanung, Zubereitung und Ausführung von Außen- und Innenputzen. Außenputz
CommitteeB/519
ISBN978 0 580 98042 8
PublisherBSI
FormatA4
DeliveryYes
Pages76
File Size2.908 MB
Price£280.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


BSOL

Access, view and download standards with multiple user access, across multiple sites with BSOL


Develop a PAS

Develop a fast-track standardization document in 9-12 months


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version