ASTM F2391 - 05(2016) - Standard Test Method for Measuring Package and Seal Integrity Using Helium as the Tracer Gas

ASTM F2391 - 05(2016)

Standard Test Method for Measuring Package and Seal Integrity Using Helium as the Tracer Gas

Status : Current   Published : April 2016



1.1 This test method includes several procedures that can be used for the measurement of overall package and seal barrier performance of a variety of package types and package forms, as well as seal/closure types. The basic elements of this method include:

1.1.1 Helium (employed as tracer gas),

1.1.2 Helium leak detector (mass spectrometer), and

1.1.3 Package/product-specific test fixtures.

1.1.4 Most applications of helium leak detection are destructive, in that helium needs to be injected into the package after the package has been sealed. The injection site then needs to be sealed/patched externally, which often destroys its saleability. Alternatively, if helium can be incorporated into the headspace before sealing, the method can be non-destructive because all that needs to be accomplished is to simply detect for helium escaping the sealed package.

1.2 Two procedures are described; however the supporting data in Section 14 only reflects Procedure B (Vacuum Mode). The alternative, Sniffer Mode, has proven to be a valuable procedure for many applications, but may have more variability due to exactly the manner that the operator conducts the test such as whether the package is squeezed, effect of multiple small leaks compared to fewer large leaks, background helium concentration, package permeability and speed at which the scan is conducted. Further testing to quantify this procedure’s variability is anticipated, but not included in this version.

1.2.1  Procedure A: Sniffer Mode—the package is scanned externally for helium escaping into the atmosphere or fixture.

1.2.2  Procedure B: Vacuum Mode—the helium containing package is placed in a closed fixture. After drawing a vacuum, helium escaping into the closed fixture (capture volume) is detected. Typically, the fixtures are custom made for the specific package under test.

1.3 The sensitivity of the method can range from the detection of:

1.3.1 Large leaks—10 -2 Pa·m 3/s to 10 -5 Pa·m 3/s (10 –1 cc/sec/atm to 10 -4 cc/sec/atm).

1.3.2 Moderate leaks—10 -5 Pa·m 3/s to 10 -7 Pa·m 3/s (10 -4 cc/sec/atm to 10 -6 cc/sec/atm).

1.3.3 Fine leaks—10 -7 Pa·m 3/s to 10 -9 Pa·m 3/s (10 -6 cc/sec/atm to 10 -8 cc/sec/atm).

1.3.4 Ultra-Fine leak—10 -9 Pa·m 3/s to 10 -11 Pa·m 3/s (10 -8 cc/sec/atm to 10 -10 cc/sec/atm).

Note 1:  Conversion from cc/sec/atm to Pa·m 3/s is achieved by multiplying by 0.1.

1.4 The terms large, moderate, fine and ultra-fine are relative terms only and do not imply the acceptability of any leak rate. The individual application dictates the level of integrity needed. For many packaging applications, only “large leaks” are considered unacceptable and the ability to detect smaller leaks is immaterial. All leak rates referred to in this method are based on conversion of actual conditions (based on partial pressure of helium) to one atmosphere pressure differential and standard temperature conditions.

1.5 The method may have applicability to any package type:

1.5.1 Flexible,

1.5.2 Semi-rigid, or

1.5.3 Rigid.

1.6 The sensitivities reported in the supporting data for this method pertain to the detectability of helium emanating from the sample and are not a function of the packaging form.

1.7 The method is not applicable to breathable or porous packaging.

1.8 The results obtained can be qualitative, semi-quantitative or quantitative depending on the procedure used.

1.9 Test fixture design is not within the scope of this method except to note that different designs will be needed for different applications (which have different package types and package integrity requirements). Furthermore, the fixture selection and design will be based on where the testing is to be conducted within the manufacturing process (in other words, quality control versus research).

1.10  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard NumberASTM F2391 - 05(2016)
TitleStandard Test Method for Measuring Package and Seal Integrity Using Helium as the Tracer Gas
Publication Date01 April 2016
Normative References(Required to achieve compliance to this standard)No other standards are normatively referenced
Informative References(Provided for Information)No other standards are informatively referenced
Descriptors Blister packaging, Bottles, Cartridges, Flexible packaging, Gas barrier performance, Helium leak test, Impermeable packaging (and materials), Integrity monitoring, Mass spectrometer, Mass spectrometer leak test, Mass spectrometer sensor, Pass/fail criteria, Pass/fail levels, Package integrity monitoring, Package integrity test, Permeable packaging (and materials), Pouch packaging, Seal integrity monitoring, Seal integrity test, Sniffer probe leak test, Sterility barrier performance, Vacuum leak test, Vapor barrier performance, Rigid packaging, Vials
File Size100 KB

 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents

Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version

Worldwide Standards
We can source any standard from anywhere in the world


The faster, easier way to work with standards