BS EN 334:2019 - Gas pressure regulators for inlet pressure up to 10 MPa (100 bar)

BS EN 334:2019

Gas pressure regulators for inlet pressure up to 10 MPa (100 bar)

Status : Current   Published : September 2019

Format
PDF

Format
HARDCOPY



This European Standard specifies constructional, functional, testing, marking, sizing and documentation requirements of gas pressure regulators: - for inlet pressures up to 100 bar and nominal diameters up to DN 400; - for an operating temperature range from - 20 °C to +60 °C, which operate with fuel gases of the 1st and 2nd family as defined in EN 437:2003+A1:2009, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations. "Gas pressure regulators" hereafter will be called "regulators" except in the titles. For standard regulators when used in pressure regulating stations complying with EN 12186 or EN 12279, the Annex ZA lists all applicable essential safety requirements of the European legislation on pressure equipment except external and internal corrosion resistance for applications in corrosive environment. This document considers the following temperature classes/types of regulators: - temperature class 1: operating temperature range from ?10 °C to 60 °C; - temperature class 2: operating temperature range from ?20 °C to 60 °C; - type IS: (integral strength type); - type DS: (differential strength type). This document applies to regulators which use the pipeline gas as a source of control energy unassisted by any external power source. The regulator may incorporate a second regulator, used as monitor, complying with the requirements in this document. The regulator may incorporate a safety shut off device (SSD) complying with the requirements of EN 14382. The regulator may incorporate a creep (venting) relief device, complying with the requirements in Annex E and/or a vent limiter, complying with the requirements in Annex I. This document does not apply to: - regulators upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters; - regulators designed to be incorporated into pressure control systems used in service lines ) with volumetric flow rate ? 200 m3/h at normal conditions and inlet pressure ? 5 bar; - regulators for which a specific document exists (e.g. EN 88-1 and EN 88-2, etc.); - industrial process control valves in accordance with EN 1349. The normative Annex G of this document lists some suitable materials for pressure bearing parts, inner metallic partition walls, auxiliary devices, integral process and sensing lines, connectors and fasteners. Other materials may be used when complying with the restrictions given in Table 5. Continued integrity of gas pressure regulators is ensured by suitable surveillance checks and maintenance. For periodic functional checks and maintenance it is common to refer to national regulations/standards where existing or users/manufacturers practices. This document has introduced the reaction of the pressure regulators to the specified reasonable expected failures in terms of "fail close" and "fail open" pressure regulator types, but it should be considered that there are other types of failures whose consequences can bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards will be reduced by a suitable surveillance in use / maintenance. In this document, both pressure regulators that can be classified as "safety accessories" by themselves (monitors) according to European legislation on pressure equipment as well as regulators that can be used to provide the necessary pressure protection through redundancy (e.g. pressure regulator with integrated safety shut-off device, pressure regulator + in-line monitor, pressure regulator + safety shut off device) are considered. The provisions in this document are in line with the state of art at the moment of writing.




Standard NumberBS EN 334:2019
TitleGas pressure regulators for inlet pressure up to 10 MPa (100 bar)
StatusCurrent
Publication Date03 September 2019
Normative References(Required to achieve compliance to this standard)EN ISO 15613:2004, EN ISO 12156-1:2018, ISO 3419:1981, EN ISO 9606-1:2017, EN ISO 175:2010, EN ISO 15610:2003, EN ISO 15612:2018, EN ISO 9606-3:1999, EN ISO 9712:2012, EN ISO 15611:2003, EN 60534-2-1:2011, EN 1092-4:2002, EN 10204:2004, EN 60534-2-3:2016, EN 14382:2019, EN 1759-4:2003, EN 13906-2:2013, EN 12279:2000/A1:2005, EN 1092-1:2018, EN 10226-1:2004, EN 13906-1:2013, EN 1092-3:2003/AC:2004, EN 1759-1:2004, EN 13906-3:2014, EN 60534-3-1:2000, EN 13445-4:2014/A1:2016, BS EN 14382:2019, ISO 1817:2015, EN 1092-2:1997, EN 1349:2009, EN 12516-1:2014+A1:2018, ISO 7005-2:1988, EN 12516-2:2014, EN 10226-2:2005, EN 1759-3:2003/AC:2004, EN 12516-4:2014+A1:2018, EN 12186:2014, EN ISO 148-1:2016, EN ISO 9606-4:1999, EN 549:1994, EN ISO 17637:2016, EN ISO 15614-1:2017, EN ISO 15614-2:2005/AC:2009, EN ISO 15609-1:2004, EN ISO 14732:2013, EN ISO 15607:2003, EN ISO 9606-2:2004
Informative References(Provided for Information)EN 88-1:2011+A1:2016, EN 88-2:2007, EN 60534-8-3:2011, EN 437:2018, EN 60534-3-2:2001, EN 12732:2013+A1:2014, EN 60534-1:2005, ISO 5752, EN ISO 14025:2010, EN 14717, EN ISO 9001:2015, EN 61672-1, EN ISO 14024:2018, EN ISO 6708:1995, EN ISO/IEC 17050-1, EN 60534-8-3, EN ISO 14021:2016, ASME PTC 60, EN ISO/IEC 17065:2012, EN 12627, EN 60534-2-1, EN ISO/IEC 17025
ReplacesBS EN 334:2005+A1:2009
International RelationshipsEN 334:2019
Draft Superseded By16/30334287 DC
DescriptorsTest equipment, Mathematical calculations, Pressure regulators, Flow regulators, Gas valves
ICS23.060.40
Title in FrenchRégulateurs de pression de gaz pour des pressions amont jusqu’à 100 bar
Title in GermanGas-Druckregelgeräte für Eingangsdrücke bis 10 MPa (100 bar)
CommitteeGSE/32
ISBN978 0 580 92588 7
PublisherBSI
FormatA4
DeliveryYes
Pages152
File Size2.011 MB
Price£342.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


BSOL

The faster, easier way to work with standards


Develop a PAS

Develop a fast-track standardization document in 9-12 months


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version