BS EN 62196-2:2017 - Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles. Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories

BS EN 62196-2:2017

Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles. Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories

Status : Current, Work in hand   Published : May 2017

Format
PDF

Format
HARDCOPY



This part of IEC 62196 applies to plugs, socket-outlets, vehicle connectors and vehicle inlets with pins and contact-tubes of standardized configurations, herein referred to as accessories. They have a nominal rated operating voltage not exceeding 480 V a.c., 50 Hz to 60 Hz, and a rated current not exceeding 63 A three-phase or 70 A single phase, for use in conductive charging of electric vehicles.

This part of IEC 62196 covers the basic interface accessories for vehicle supply as specified in IEC 62196‑1, and intended for use in conductive charging systems for circuits specified in IEC 61851‑1:2010.

NOTE 1

Electric road vehicles (EV) implies all road vehicles, including plug-in hybrid road vehicles (PHEV), that derive all or part of their energy from RESS.

These accessories are intended to be used for circuits specified in IEC 61851‑1:2010 which operate at different voltages and frequencies and which may include extra-low voltage (ELV) and communication signals.

These accessories may be used for bidirectional power transfer (under consideration).

This standard applies to accessories to be used in an ambient temperature between –30 °C and +50 °C.

NOTE 2

In the following country, other requirements regarding the lower temperature may apply: NO.

NOTE 3

In the following country, –35 °C applies: SE.

These accessories are intended to be connected only to cables with copper or copper-alloy conductors.

Vehicle inlet and vehicle connector to this standard are intended to be used for charging in modes 1, 2 and 3, cases B and C. The socket-outlets and plugs covered by this standard are intended to be used for charging mode 3 only, case A and B.

The modes and permissible connections are specified in IEC 62196‑1:2014.




Standard NumberBS EN 62196-2:2017
TitlePlugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles. Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories
StatusCurrent, Work in hand
Publication Date24 May 2017
Normative References(Required to achieve compliance to this standard)IEC 62196-1:2014, EN 62196-1:2014
Informative References(Provided for Information)No other standards are informatively referenced
ReplacesBS EN 62196-2:2012+A12:2014
International RelationshipsEN 62196-2:2017,IEC 62196-2:2016
Draft Superseded By14/30311590 DC
DescriptorsElectric charge, Electrical conductance, Electric power systems, Electrical connections, Electric connectors, Electric sockets, Electrically-operated devices, Road vehicles
ICS29.120.30
43.120
Title in FrenchFiches, socles de prise de courant, prises mobiles de véhicule et socles de connecteurs de véhicule. Charge conductive des véhicules électriques Exigences dimensionnelles de compatibilité et d'interchangeabilité pour les appareils à broches et alvéoles pour courant alternatif
Title in GermanStecker, Steckdosen, Fahrzeugkupplungen und Fahrzeugstecker. Konduktives Laden von Elektrofahrzeugen Anforderungen und Hauptmaße für die Kompatibilität und Austauschbarkeit von Stift- und Buchsensteckvorrichtungen für Wechselstrom
CommitteePEL/23/4
ISBN978 0 580 87759 9
PublisherBSI
FormatA4
DeliveryYes
Pages68
File Size5.609 MB
Price£254.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Worldwide Standards
We can source any standard from anywhere in the world


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version


Develop a PAS

Develop a fast-track standardization document in 9-12 months


Customers who bought this product also bought

  • BS EN 62196-1:2014
    Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles General requirements
  • BS EN 62196-3:2014
    Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers