ASTM F2332 - 06(2013) - Standard Specification for Annular Ball Bearings for Instruments and Precision Rotating Components

ASTM F2332 - 06(2013)

Standard Specification for Annular Ball Bearings for Instruments and Precision Rotating Components

Status : Current   Published : January 2013

Format
PDF

Format
HARDCOPY



1.1 This specification covers annular ball bearings intended primarily for use in instrument and precision rotating components. Instrument and precision ball bearings should meet tolerances specified in ABMA Standard 12.2, Instrument Ball Bearings Inch Design for Classes ABEC 5P and 7P.

1.2  Intended Use—Ball bearings defined by this specification are intended for use in critical components of instrument systems. Such components range from air circulating blowers and drive motors through precision gear trains, gyro gimbals, and pickoffs to rate integrating spin-motors.

1.3 The specification contains many of the requirements of MIL-B-81793, which was originally developed by the Department of Defense and maintained by the Naval Air Systems Command (Navy-AS) in Lakehurst, NJ. The following government activity codes may be found in the Department of Defense, Standardization Directory SD-1. 2

[This table has been removed.]


1.4  Classification—Annular ball bearings for instrument and precision rotating components shall be of the following types, as specified:

1.4.1  Type I—Annular ball bearing, for instruments and precision rotating components, deep groove, unflanged; (See Annex A1 –Annex A4)

1.4.2  Type II—Annular ball bearing, for instruments and precision rotating components, deep groove, flanged; (See Annex A5 –Annex A8)

1.4.3  Type III—Annular ball bearing, for instruments and precision rotating components, deep groove, unflanged, inner ring extended; (See Annex A9 –Annex A12)

1.4.4  Type IV—Annular ball bearing, for instruments and precision rotating components, deep groove, flanged, inner ring extended; (See Annex A13 –Annex A16)

1.4.5  Type V—Annular ball bearing, for instruments and precision rotating components, angular contact, unflanged, nonseparable, and counterbored outer ring; (See Annex A17 –Annex A20)

1.4.6  Type VI—Annular ball bearing, for instruments and precision rotating components, angular contact, flanged, nonseparable, and counterbored outer ring on flange side; (See Annex A21 –Annex A24)

1.4.7  Type VII—Annular ball bearing, for instruments and precision rotating components, angular contact, unflanged, separable, and stepped inner ring; (See Annex A25 –Annex A28)

1.4.8  Type VIII—Annular ball bearing, for instruments and precision rotating components, angular contact, flanged, separable, and stepped inner ring; (See Annex A29 –Annex A32)

1.4.9  Type IX—Annular ball bearing, for instruments and precision rotating components, angular contact, unflanged, nonseparable, and stepped inner ring. (See Annex A33 –Annex A36)

1.5  Inch-Pound Specification—This specification covers only the inch-pound bearings.

1.5.1 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.6  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.




Standard NumberASTM F2332 - 06(2013)
TitleStandard Specification for Annular Ball Bearings for Instruments and Precision Rotating Components
StatusCurrent
Publication Date05 January 2013
Normative References(Required to achieve compliance to this standard)No other standards are normatively referenced
Informative References(Provided for Information)No other standards are informatively referenced
Descriptors ABEC 5P, ABEC 7P, Angular contact, Barrier coating, Bearing void, Calibration (classification), Contact angle, Counterbored outer ring, Deep groove radial, Extended inner ring, Instrument bearing, Nonseparable, Passivation, Precision bearing, Separable, Starting torque, Stepped inner ring
ICS21.100.10
PublisherASTM
FormatA4
DeliveryYes
Pages144
File Size0 KB
Price£83.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


BSOL

The faster, easier way to work with standards


Develop a PAS

Develop a fast-track standardization document in 9-12 months


Worldwide Standards
We can source any standard from anywhere in the world