BS EN 15383:2012+A1:2013 - Plastics piping systems for drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP). Manholes and inspection chambers

BS EN 15383:2012+A1:2013

Plastics piping systems for drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP). Manholes and inspection chambers

Status : Current   Published : January 2013

Format
PDF

Format
HARDCOPY



This European Standard applies to a) manholes, when made from glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP); b) inspection chambers, when made from glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP) which are intended to be used with inverts which are at a depth not exceeding 2 m. These products are intended to be used within a drain or sewer system operating without pressure or occasionally at a head of pressure up to 1 bar. It applies to products, and their joints, intended for use in buried installations and to be installed by open-trench techniques. The units have a circular shape with nominal sizes not exceeding the maximum nominal size specified in EN 14364. The intended use of these products is to provide access to, buried drain or sewer systems for the conveyance of waste water at temperatures up to 50 °C, without pressure or occasionally at a head of pressure up to 1 bar, outside buildings and installed in areas subjected to vehicle and/or pedestrian traffic. It specifies definitions including symbols, requirements and characteristics of manholes, inspection chambers, joints, materials, test methods and marking. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections, taking into account their particular requirements and any relevant national regulations and installation practices or codes.




Standard NumberBS EN 15383:2012+A1:2013
TitlePlastics piping systems for drainage and sewerage. Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP). Manholes and inspection chambers
StatusCurrent
Publication Date31 January 2013
Normative References(Required to achieve compliance to this standard)EN 124, EN 476, EN 681-1, EN 1119, EN 1917, EN 13101, EN 14364:2006/AMD 1:2008, EN 14396, CEN/TS 14632, EN ISO 604:2003, ISO 604:2002, EN ISO 3126, ISO 3126, ISO 2602, ISO 8533, EN 14364:2006
Informative References(Provided for Information)No other standards are informatively referenced
International RelationshipsEN 15383:2012
Amended ByAmendment, October 2013. Amends and replaces BS EN 15383:2012.
Draft Superseded By05/30141329 DC10/30237537 DC
DescriptorsPlastics, Pipework systems, Pipes, Drainage, Sewerage, Sewers, Water supply and waste systems (buildings), Glass fibres, Reinforced materials, Polyesters, Thermosetting polymers, Pipe fittings, Pipe couplings, Plastic pipelines, Dimensions, Dimensional tolerances, Size, Pressure, Performance, Mechanical properties of materials, Test methods, Unsaturated polyesters
ICS93.030
Title in FrenchSystèmes de canalisations en plastique pour les branchements et collecteurs d'assainissement. Plastiques thermodurcissables renforcés de verre (PRV) à base de résine de polyester (UP). Regards et boîtes de branchement et d'inspection
Title in GermanKunststoff Rohrleitungssysteme für Abwasserleitungen und-kanäle. Glasfaserverstärkte duroplastische Kunststoffe (GFK) auf der Basis von Polyesterharz (UP). Einsteig- und Kontrollschächte
CommitteePRI/88/2
ISBN978 0 580 82220 9
PublisherBSI
FormatA4
DeliveryYes
Pages34
File Size1.497 MB
Price£214.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version


BSOL

The faster, easier way to work with standards


Develop a PAS

Develop a fast-track standardization document in 9-12 months