ASTM D7743 - 12 - Standard Test Method for Measuring the Minimum Fluidization Velocities of Free Flowing Powders

ASTM D7743 - 12

Standard Test Method for Measuring the Minimum Fluidization Velocities of Free Flowing Powders

Status : Current   Published : January 2012



1.1 This test method describes the apparatus and procedure needed for determining the minimum fluidization velocity of Geldart Group A powders and the minimum fluidization or complete fluidization velocity of Geldart Group B powders.

1.1.1 This test method is for powders that are readily or easily fluidizable and fall into the category of Group A and B of the “Geldart” classification. The fluidization of Geldart Group C powders will be addressed in another standard. This test method could apply to Geldart Group D particles but the focus of this document is towards Group and A and B materials.

1.1.2 Geldart classification of powders is often defined by comparing the Sauter mean particle size with the difference between the particle density and the density of the fluidizing gas, as illustrated in Fig. 1( 1). 2

[This image has been removed.]

FIG. 1 Geldart Classification of Particles Group A powders are easily fluidized but there is a difference between the gas velocity where the bed is initially fluidized and the velocity where bubbles are first observed. For Group A powders, bed expansion can be considerable before any bubbles are observed. Group B powders are also easily fluidized; but there is no difference between the velocity where the bed is fluidized and the velocity at the onset of bubbling. The minimum gas velocity, where all of the particles are fully supported by the gas for Group B powders, is often referred to as the “complete fluidization velocity” instead of minimum fluidization velocity. Group C powders are cohesive and can be difficult to fluidize. Group A powders can be distinguished from Group B powders by the response to deaeration. Group A powders deaerate relatively slowly whereas Group B powders deaerate almost instantaneously in fluidized beds. Group A Powders that lie near or on the Group A/C boundary may be tested by this method. However, if the powders do not fluidize freely, test results should be considered invalid. Temperature, moisture (water) content, particle size distribution, particle shape and sometimes other variables influence the Geldart classification of a powder. Deaeration testing specified in is a more definitive test than simply using particle size and density differences as described in 1.1.2.

Note 1A Standard Practice for deaeration testing is under development.

1.2 This test method should be performed in a laboratory under controlled conditions of temperature and humidity.

1.3 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.

1.3.1 The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition they are representative of the significant digits that generally should be retained. The procedures used do not consider material variations, the purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.

1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard NumberASTM D7743 - 12
TitleStandard Test Method for Measuring the Minimum Fluidization Velocities of Free Flowing Powders
Publication Date06 January 2012
Normative References(Required to achieve compliance to this standard)No other standards are normatively referenced
Informative References(Provided for Information)No other standards are informatively referenced
Descriptors Complete fluidization, Fluidization, Geldart Group A, Geldart Group B, Minimum bubbling velocity, Minimum fluidization velocity
File Size347.2 KB

 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


The faster, easier way to work with standards

Worldwide Standards
We can source any standard from anywhere in the world

Develop a PAS

Develop a fast-track standardization document in 9-12 months