BS EN 14364:2013 - Plastics piping systems for drainage and sewerage with or without pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Specifications for pipes, fittings and joints

BS EN 14364:2013

Plastics piping systems for drainage and sewerage with or without pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Specifications for pipes, fittings and joints

Status : Current, Project Underway   Published : March 2013

Format
PDF

Format
HARDCOPY



This European Standard specifies the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage, including culverts, with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together. It is the responsibility of the purchaser or specifier to make the appropriate selections taking into account their particular requirements and any relevant national regulations and installation practices or codes. This European Standard is applicable to GRP-UP, with flexible or rigid joints (see 3.33 and 3.34), primarily intended for use in buried installations. NOTE Piping systems conforming to this European Standard can be used also for non-buried applications provided that the influence of the environment, e.g. from UV-radiation, and the supports are considered in the design of the pipes, fittings and joints. It is applicable to pipes, fittings and their joints of nominal sizes from DN 100 to DN 4000, which are intended to be used for the conveyance of surface water or sewage at temperatures up to 50 °C, with or without pressure. This European Standard covers a range of nominal sizes, nominal stiffnesses and nominal pressures. Clause 6 is applicable to fittings made using any of the following techniques: a) fabricated from straight pipe; b) moulded by: 1) filament winding; 2) tape winding; 3) contact moulding; 4) hot or cold press moulding. This European standard is applicable to the joints to be used in GRP-UP piping systems to be used for the conveyance of water, both buried and non-buried. It is applicable to joints, which are or are not intended to be resistant to axial loading. It covers requirements to prove the design of the joint. It specifies type test performance requirements for the following joints as a function of the declared nominal pressure rating of the pipeline or system: c) socket-and-spigot (either integral with pipe or sleeve coupling) or mechanical joint; d) locked socket-and-spigot joint; e) cemented or wrapped joint; f) bolted flange joint. Recommended practices for the installation of buried pipes made in accordance with this standard is addressed in CEN/TS 14578. Guidelines for the structural analysis of buried GRP-UP pipelines are addressed in CEN/TS 14807. Guidance for the Assessment of Conformity of products made in accordance with this standard is addressed in CEN/TS 14632.




Standard NumberBS EN 14364:2013
TitlePlastics piping systems for drainage and sewerage with or without pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Specifications for pipes, fittings and joints
StatusCurrent, Project Underway
Publication Date31 March 2013
Normative References(Required to achieve compliance to this standard)ISO 10466, CEN/TS 14578, ISO 10468, EN ISO 1452-3, ISO 4200, ISO 10928:2016, EN 681-1, BS ISO 7432:2018, ISO 2531, ISO 7432:2018, ISO 8513, CEN/TS 14632, EN 1447, CEN/TS 14807, ISO 8521, ISO/TR 10465-3, ISO 527-4, EN 1119, ISO 527-5, EN ISO 75-2:2004, ISO 75-2:2004, ISO 3126, ISO 1452-3, EN ISO 527-5, ISO 8533, ISO 8483, EN ISO 527-4, EN ISO 3126, ISO 10471, ISO 10952, ISO 7685, ISO 10928, ISO 11922-1
Informative References(Provided for Information)ISO 2078, EN 476, EN ISO 2078
ReplacesBS EN 14364:2006+A1:2008
International RelationshipsEN 14364:2013
Draft Superseded By11/30246458 DC
DescriptorsDimensions, Pressure, Size, Performance, Test methods, Dimensional tolerances, Thermosetting polymers, Polyesters, Pipe fittings, Plastic pipelines, Sewers, Pipe couplings, Drainage, Unsaturated polyesters, Sewerage, Mechanical properties of materials, Glass fibres, Pipes, Plastics, Reinforced materials, Pipework systems, Water supply and waste systems (buildings)
ICS23.040.20
93.030
Title in FrenchSystèmes de canalisations en plastique pour l'évacuation et l'assainissement avec ou sans pression. Plastiques thermodurcissables renforcés de verre (PRV) à base de résine de polyester non saturé (UP). Spécifications pour tubes, raccords et assemblages
Title in GermanKunststoff-Rohrleitungssyteme für Abwasserleitungen und kanäle mit oder ohne Druck. Glasfaserverstärkte duroplastische Kunststoffe (GFK) auf der Basis von ungesättigtem Polyesterharz (UP). Festlegungen für Rohre, Formstücke und Verbindungen
CommitteePRI/88/2
ISBN978 0 580 75373 2
PublisherBSI
FormatA4
DeliveryYes
Pages76
File Size1.295 MB
Price£274.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version


BSOL

The faster, easier way to work with standards


Worldwide Standards
We can source any standard from anywhere in the world


Customers who bought this product also bought

  • BS EN 1796:2013
    Plastics piping systems for water supply with or without pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)