BS EN 14758-1:2012 - Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifiers (PP-MD). Specifications for pipes, fittings and the system

BS EN 14758-1:2012

Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifiers (PP-MD). Specifications for pipes, fittings and the system

Status : Under review, Current   Published : April 2012

Format
PDF

Format
HARDCOPY



This European Standard specifies the requirements for solid-wall pipes, fittings and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and non- pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure. This is reflected in the marking of products by "U" and "UD". It also specifies the test parameters for the test methods referred to in this European Standard. This European Standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. In conjunction with Part 2 and Part 3 of EN 14758 (see Foreword) it is applicable to PP-MD pipes and fittings, their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage. This European Standard is applicable to PP-MD pipes with or without an integral socket. NOTE 2 The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings. NOTE 3 Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 13. NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 13.




Standard NumberBS EN 14758-1:2012
TitlePlastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifiers (PP-MD). Specifications for pipes, fittings and the system
StatusUnder review, Current
Publication Date30 April 2012
Confirm Date12 May 2019
Normative References(Required to achieve compliance to this standard)ISO 472:1999, EN 681-1, EN 681-2, EN ISO 3126, EN ISO 9969, ISO 9969, ISO 13259, ISO 1043-1:2001, EN ISO 580:2005, ISO 2505:2005, ISO 11173, ISO 13257, ISO 3127, ISO 13967, ISO 13968, ISO 580:2005, EN ISO 1167, ISO 1133:2005, ISO 13264, EN ISO 1043-1:2001, ISO 13263, EN ISO 13967, EN ISO 13968, EN ISO 472:2001, EN ISO 1133:2005, EN ISO 2505:2005, ISO 3126
Informative References(Provided for Information)ISO 4065, EN 1852-1:2018, EN 295-3, RAL 840-HR, ISO 11922-1, ISO/TR 7620, EN ISO 9967, ISO 265-1, EN 1401-1, EN 476, ISO 9967, ISO/TR 10358, ISO 8773, EN 12666-1
ReplacesBS EN 14758-1:2005+A1:2009
International RelationshipsEN 14758-1:2012
Draft Superseded By11/30246452 DC
DescriptorsPlastic pipelines, Sewers, Additives, Minerals, Drainage, Pipework systems, Underground, Plastics, Polypropylene, Performance, Pipes, Thermoplastic polymers, Sewerage, Dimensions, Water supply and waste systems (buildings)
ICS23.040.01
93.030
Title in Frenchystèmes de canalisations en plastique pour les branchements et les collecteurs d'assainissement enterrés sans pression. Polypropylène avec modificateurs minéraux (PP-MD). Spécifications pour les tubes, les raccords et le système
Title in GermanSKunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -leitungen. Polypropylen mit mineralischen Additiven (PP-MD). Anforderungen an Rohre, Formstücke und das Rohrleitungssystem
CommitteePRI/88/1
ISBN978 0 580 75371 8
PublisherBSI
FormatA4
DeliveryYes
Pages38
File Size1.261 MB
Price£214.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Develop a PAS

Develop a fast-track standardization document in 9-12 months


BSOL

The faster, easier way to work with standards


Worldwide Standards
We can source any standard from anywhere in the world