BS EN 848-3:2012 - Safety of woodworking machines. One side moulding machines with rotating tool. Numerically controlled (NC) boring and routing machines

BS EN 848-3:2012

Safety of woodworking machines. One side moulding machines with rotating tool. Numerically controlled (NC) boring and routing machines

Status : Superseded, Withdrawn   Published : November 2012 Replaced By : BS EN ISO 19085-3:2017

WITHDRAWN TITLE
*To ask about withdrawn titles contact the
BSI Customer Services
cservices@bsigroup.com, +44 345 086 9001


This European Standard specifies all significant hazards, hazardous situations and events as listed in Clause 4, which are relevant to NC boring machines, NC routing machines and NC combined boring/routing machines (as defined in 3.1) herein after referred to as "machines" designed to cut solid wood, chip board, fibreboard, plywood and also these materials where these are covered with plastic/light alloy laminate or edgings when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Machines which are designed to work wood based materials may also be used for working hardened plastic materials with similar physical characteristics as wood. This document also applies to machines fitted with: - additional equipment for sawing, sanding, edge banding or assembly units and dowel devices; - fixed or movable workpiece support; - mechanical, pneumatic, hydraulic or vacuum workpiece clamping; - automatic tool change facilities. This document does not deal with the specific hazards of edge banding equipment fitted to NC boring machines, NC routing machines and NC combined boring/routing machines. This document is only applicable to NC boring machines, NC routing machines and NC combined boring/routing machines which are designed to use milling tools with a cutting circle diameter below 16 mm or milling tools or saw-blades conforming to EN 847-1:2005+A1:2007 and EN 847-2:2001 and boring tools or sanding wheels. This document is not applicable to NC boring machines, NC routing machines and NC combined boring/routing machines which are designed to use grinding wheels. This document is not applicable to single spindle hand fed/integrated fed routing machines. NOTE Single spindle hand fed/integrated fed routing machines are dealt with in EN 848-2:2007+A1:2009. This document does not deal with the specific hazards of ejection through openings on machines where the distance between the work-piece support and the lower edge of the partial enclosure exceeds 400 mm. This document is not applicable to NC boring machines, NC routing machines and NC combined boring/routing machines which are manufactured before the date of its publication as EN.




Standard NumberBS EN 848-3:2012
TitleSafety of woodworking machines. One side moulding machines with rotating tool. Numerically controlled (NC) boring and routing machines
StatusSuperseded, Withdrawn
Publication Date30 November 2012
Withdrawn Date16 May 2018
Normative References(Required to achieve compliance to this standard)EN 1760-3:2004/AMD 1:2009, EN ISO 13850:2008, EN 60439-1:1999, ISO 4413:2010, EN ISO 11202:2010, EN ISO 3743-1:2010, ISO 4414:2010, ISO 12100:2010, EN 60825-1:2007, EN 12779:2004/AMD 1:2009, EN 1088:1995/AMD 2:2008, IEC 60529:1989, IEC 61800-5-2:2007, EN 60204-1:2006, EN 1760-1:1997/AMD 1:2009, EN 1037:1995/AMD 1:2008, IEC 60439-1:1999, ISO 11204:2010, EN 1005-3:2002/AMD 1:2008, EN 1005-1:2001/AMD 1:2008, EN 1005-2:2003/AMD 1:2008, EN ISO 11688-1:2009, EN ISO 3744:2010, EN 1005-4:2005/AMD 1:2008, IEC 61496-2:2006, ISO 7960:1995, ISO 4871:1996, EN 847-2:2001, EN 50370-2:2003, ISO 3743-2:1994, ISO 9614-1:1993, ISO 13850:2006, EN 60529:1991, ISO/TR 11688-1:1995, EN 50370-1:2005, ISO 11202:2010, EN 894-3:2000/AMD 1:2008, EN ISO 3746:2010, EN 61800-5-2:2007, EN ISO 4871:2009, ISO 3745:2003, EN 847-1:2005/AMD 1:2007, IEC 60825-1:2007, EN 894-1:1997/AMD 1:2008, EN ISO 13857:2008, ISO 3744:2010, EN 1837:1999/AMD 1:2009, ISO 3746:2010, ISO 13857:2008, EN ISO 3745:2009, ISO 13849-1:2006, IEC 60204-1:2005, IEC 61496-1:2004, EN 894-2:1997/AMD 1:2008, CLC/TS 61496-2:2006, EN
Informative References(Provided for Information)EN 62061:2005, IEC 60947-4-1:2009, HD 22.1 S4:2002, EN 60947-5-1:2004, IEC 60947-5-1:2003, EN 349:1993/AMD 1:2008, EN 614-1:2006/AMD 1:2009, 2006/42/EC, EN 614-2:2000/AMD 1:2008, EN 848-2:2007/AMD 1:2009, HD 21.1 S4:2002, EN 1093-11:2001/AMD 1:2008, EN ISO 11688-2:2000, EN 61508-2:2010, IEC 62061:2005, IEC 61508-1:2010, EN 60947-4-1:2010, IEC 61508-2:2010, EN 1093-9:1998/AMD 1:2008, IEC 61508-4:2010, EN 61508-4:2010, EN 61508-1:2010, ISO/TR 11688-2:1998, ISO 14:1982
Replaced ByBS EN ISO 19085-3:2017
ReplacesBS EN 848-3:2007+A2:2009
International RelationshipsEN 848-3:2012
Draft Superseded By10/30233212 DC
DescriptorsHazards, Equipment safety, Control systems, Electrical safety, Boring machines, Moulding equipment, Control devices, Routing machines, Enclosures, Rotating parts, Stopping, Noise (environmental), Safety devices, Numerical control, Mechanical testing, Stability, Occupational safety, Testing conditions, Access, Machine tools, Starting, Rotating electric machines, Production equipment, Performance testing, Instructions for use, Machine guards, Woodworking, Velocity control, Woodworking machines, Safety measures
ICS79.120.10
Title in FrenchSécurité des machines pour le travail du bois. Machines à fraiser sur une face à outils rotatifs. Perceuses et défonceuses à commande numérique
Title in GermanSicherheit von Holzbearbeitungsmaschinen. Fräsmaschinen für einseitige Bearbeitung mit drehendem Werkzeug. NC-Bohr- und Fräsmaschinen
CommitteeMTE/23
ISBN978 0 580 72605 7
PublisherBSI
FormatA4
DeliveryYes
Pages88
File Size1.413 MB
Price£274.00


WITHDRAWN TITLE
*To ask about withdrawn titles contact the
BSI Customer Services
cservices@bsigroup.com, +44 345 086 9001
 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version


Collaborate, Innovate, Accelerate.


Worldwide Standards
We can source any standard from anywhere in the world