BS EN 62196-3:2014 - Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles. Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers

BS EN 62196-3:2014

Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles. Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers

Status : Current, Work in hand   Published : December 2014

Format
PDF

Format
HARDCOPY



This part of IEC 62196 is applicable to vehicle couplers with pins and contact-tubes of standardized configuration, herein also referred to as “accessories”, intended for use in electric vehicle conductive charging systems which incorporate control means, with rated operating voltage up to 1 500 V d.c. and rated current up to 250 A, and 1 000 V a.c. and rated current up to 250 A.

This part of IEC 62196 applies to high power d.c. interfaces and combined a.c./d.c. interfaces of vehicle couplers specified in IEC 62196‑1:2014, and intended for use in conductive charging systems for circuits specified in IEC 61851‑1:2010, and IEC 61851‑23:2014.

The d.c. vehicle connectors covered by this part of the standard are used only in charging mode 4, according to Case C in Clause 6.2 of IEC 61851‑1:2010, Figure 3 in Clause 6.3.1 of IEC 61851‑1:2010 and IEC 62196‑2:2011.

The d.c. vehicle inlets covered by this part of the standard are used only in charging mode 4, according to Case C in Clause 6.2 of IEC 61851‑1:2010, Figure 3 in Clause 6.3.1 of IEC 61851‑1:2010.

These vehicle couplers are intended to be used for circuits similar to those specified in IEC 61851‑23 which operate at different voltages and which may include ELV and communication signals.

This part of IEC 62196 applies to the vehicle couplers to be used in an ambient temperature of between –30 °C and +50 °C.

NOTE 1

In some countries, other requirements may apply.

NOTE 2

In the following country, –35 °C applies: SE.

These vehicle couplers are intended to be connected only to cables with copper or copper-alloy conductors.




Standard NumberBS EN 62196-3:2014
TitlePlugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles. Dimensional compatibility and interchangeability requirements for d.c. and a.c./d.c. pin and contact-tube vehicle couplers
StatusCurrent, Work in hand
Publication Date31 December 2014
Normative References(Required to achieve compliance to this standard)EN 62196-2:2012+A11:2013, EN 62196-2:2012, IEC 62196-2:2011, EN 62196-2:2012+A12:2014
Informative References(Provided for Information)ISO 17409
International RelationshipsEN 62196-3:2014,IEC 62196-3:2014
Draft Superseded By13/30231474 DC
DescriptorsElectrically-operated devices, Electrical connections, Electric sockets, Electrical conductance, Electric plugs, Electric charge, Electric connectors, Electric power systems, Road vehicles
ICS29.120.30
43.120
Title in FrenchFiches, socles de prise de courant, prises mobiles de véhicule et socles de connecteur de véhicule. Charge conductive des véhicules électriques. Exigences dimensionnelles de compatibilité et d'interchangeabilité pour les connecteurs de véhicule à broches et alvéoles pour courant continu et pour courants alternatif et continu
Title in GermanStecker, Steckdosen und Fahrzeugsteckvorrichtungen. Konduktives Laden von Elektrofahrzeugen. Anforderungen an und Hauptmaße für Stifte und Buchsen für die Austauschbarkeit von Fahrzeugsteckvorrichtungen zum dedizierten Laden mit Gleichstrom und als kombinierte Ausführung zum Laden mit Wechselstrom/Gleichstrom
CommitteePEL/23/4
ISBN978 0 580 72195 3
PublisherBSI
FormatA4
DeliveryYes
Pages20
File Size1.104 MB
Price£134.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Worldwide Standards
We can source any standard from anywhere in the world


Develop a PAS

Develop a fast-track standardization document in 9-12 months


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version


Customers who bought this product also bought

  • BS EN 62196-1:2014
    Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles General requirements
  • BS EN 62196-2:2017
    Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories