BS EN 60695-2-10:2013 - Fire hazard testing. Glowing/hot-wire based test methods. Glow-wire apparatus and common test procedure
As part of BSI's continuing security improvements browsers that use TLS 1.0 security protocol will not be able to access this website after 18th October. If you experience issues using BSI products you can check with your IT dept. to ensure you are using an up-to-date browser. For more information please email subscription.support@bsigroup.com or call 0345 086 9001

Find Similar Items

This product falls into the following categories.

You may find similar items within these categories by selecting from the choices below:

BS EN 60695-2-10:2013

Fire hazard testing. Glowing/hot-wire based test methods. Glow-wire apparatus and common test procedure

Status : Current, Work in hand   Published : July 2013

Format
PDF

Format
HARDCOPY



IEC 60695-2-10:2013 specifies the glow-wire apparatus and common test procedure to simulate the effects of thermal stresses which may be produced by heat sources such as glowing elements or overloaded resistors, for short periods, in order to assess the fire hazard by a simulation technique. The test procedure described in this standard is a common test procedure intended for the small-scale tests in which a standardized electrically heated wire is used as a source of ignition. It is a common part of the test procedures applied to end products and to solid electrical insulating materials or other solid combustible materials. A detailed description of each particular test procedure is given in the respective standards IEC 60695-2-11, IEC 60695-2-12 and IEC 60695-2-13. This second edition of IEC 60695-2-10 cancels and replaces the first edition of IEC 60695-2-10 published in 2000. This edition constitutes a technical revision. The main changes with respect to the previous edition are as follows:


- A table of contents has been added.


- The introduction has been updated to align with other TC89 documents.


- The scope has been clarified to align with other documents in the IEC 60695-2 Glow-wire series.


- Terms and definitions relevant to this document have been added.


- Clause 4 has been deleted and the remaining clauses renumbered.


- The description of the power supply has been updated with additional details (see 4.1).


- The temperature measuring system (see 4.3) and the description of the specified layer has been updated (see 4.4).


- New guidance has been introduced to assist in the verification of the temperature measuring system (see 5.2 and Annex C).


- The common test produced has been clarified (see Clause 7).


- The tolerances have been changed for the dimensions of the glow-wire (see Figure 1).


- New guidance on flaming observations has been added (see Annex B). It has the status of a horizontal standard in accordance with

IEC Guide 104

and ISO/IEC Guide 51. Keywords: Glowing/hot-wire, Glow-wire.



This publication is to be read in conjunction with

IEC/TS 60695-2-11:2000

,

IEC 60695-2-12:2010

, and

IEC 60695-2-13:2010


Standard NumberBS EN 60695-2-10:2013
TitleFire hazard testing. Glowing/hot-wire based test methods. Glow-wire apparatus and common test procedure
StatusCurrent, Work in hand
Publication Date31 July 2013
Cross ReferencesIEC 60584-1, IEC 60584-2, IEC 60695-2-11, IEC 60695-2-12, IEC 60695-2-13, IEC Guide 104:2010, ISO/IEC Guide 51:1999, ISO 4046-4:2002, ISO 13943:2008, EN 60584-1, EN 60584-2, EN 60695-2-11, EN 60695-2-12, EN 60695-2-13, EN ISO 13943:2010, IEC 60695-1-10, IEC 60695-1-11
ReplacesBS EN 60695-2-10:2001, IEC 60695-2-10:2000
International RelationshipsEN 60695-2-10:2013,IEC 60695-2-10:2013,IEC TS 62720:2017
Draft Superseded By09/30206605 DC
DescriptorsElectrical insulating materials, Ignitability, Testing conditions, Hazards, Fire risks, Simulation, Electrical equipment, Flammability, Electronic equipment and components, Test equipment, Fire tests, Thermal stress, Wires, Electrical components
ICS01.040.35
01.060
13.220.40
29.020
35.240.60
Title in FrenchEssais relatifs aux risques du feu. Essais au fil incandescent/chauffant. Appareillage et méthode commune d'essai
Title in GermanPrüfungen zur Beurteilung der Brandgefahr. Prüfverfahren mit dem Glühdraht. Glühdrahtprüfeinrichtung und allgemeines Prüfverfahren
CommitteeGEL/89
ISBN978 0 580 68472 2
PublisherBSI
FormatA4
DeliveryYes
Pages26
File Size512 KB
Price£176.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Collaborate, Innovate, Accelerate.


BSOL

The faster, easier way to work with standards


Worldwide Standards
We can source any standard from anywhere in the world


Customers who bought this product also bought

  • BS EN 60695-2-11:2014
    Fire hazard testing Glowing/hot-wire based test methods. Glow-wire flammability test method for end-products (GWEPT)