BS EN ISO 9445-2 Continuously cold-rolled stainless steel. Tolerances on dimensions and form. Wide strip and plate/sheet

BS EN ISO 9445-2:2010

Continuously cold-rolled stainless steel. Tolerances on dimensions and form. Wide strip and plate/sheet

Status : Current, Under review   Published : March 2010

Format
PDF

Format
HARDCOPY



BS EN ISO 9445-2:2010 Continuously cold-rolled stainless steel. Tolerances on dimensions and form. Wide strip and plate/sheet

BS EN ISO 9445 consists of the following parts, under the general title Continuously cold-rolled stainless steel. Tolerances on dimensions and form:

BS EN ISO 9445 Part 2 specifies the tolerances on dimensions and form for continuously cold-rolled stainless steel wide strip and plate/sheet, in thicknesses from 0,30 mm to 8,0 mm and in rolling widths from 600 mm to 2 100 mm.

It also applies to slit cold-rolled wide strip in widths less than 600 mm manufactured from wide strip by longitudinal slitting and to cut lengths manufactured from such strip.

Contents of BS EN ISO 9445-2 include:

  • Scope
  • Normative references
  • Terms and definitions
  • Information to be supplied by the purchaser
  • Type of delivery and delivery condition
  • Preferred thicknesses
  • Tolerances on thickness for cold-rolled wide strip and products obtained from cold-rolled wide strip
  • Tolerances on width for cold-rolled wide strip and products obtained from cold-rolled wide strip
  • Preferred coil inner diameters for cold-rolled wide strip and slit cold-rolled wide strip
  • Tolerances on length for plate/sheet cut from cold-rolled wide strip and for cut lengths obtained from slit cold-rolled wide strip
  • Tolerances on edge camber for cold-rolled wide strip and products obtained from coldrolled wide strip
  • Tolerances on squareness for plate/sheet obtained from cold-rolled wide strip and cut lengths obtained from slit cold-rolled wide strip
  • Tolerances on flatness for plate/sheet obtained from cold-rolled wide strip and cut lengths obtained from slit cold-rolled wide strip
  • Edge waviness tolerances for cold-rolled strip
  • Form of coils
  • Ordered format for plate/sheet and cut lengths
  • Measurement of thickness for cold-rolled wide strip, plate/sheet cut from cold-rolled wide strip, slit cold-rolled wide strip and cut lengths obtained from slit cold-rolled wide strip
  • Measurement of width
  • Measurement of length
  • Measurement of edge camber
  • Measurement of squareness
  • Measurement of flatness and waviness

BS EN ISO 9445:2010 replaces BS EN ISO 9445:2006 which has been withdrawn.




Standard NumberBS EN ISO 9445-2:2010
TitleContinuously cold-rolled stainless steel. Tolerances on dimensions and form. Wide strip and plate/sheet
StatusCurrent, Under review
Publication Date31 March 2010
Confirm Date10 September 2014
Normative References(Required to achieve compliance to this standard)ISO 6929
Informative References(Provided for Information)No other standards are informatively referenced
ReplacesBS EN ISO 9445:2006
International RelationshipsISO 9445-2:2009,EN ISO 9445-2:2010
DescriptorsRolling, Strips, Stainless steels, Heat-treatable steels, Preferred sizes, Cold-working, Width, Rolled products, Dimensions, Sheet materials, Flatness (surface), Thickness, Dimensional measurement, Diameter, Form tolerances, Dimensional tolerances
ICS77.140.20
77.140.50
Title in FrenchAcier inoxydable laminé à froid en continu. Tolérances sur les dimensions et la forme. Larges bandes et tôles
Title in GermanKontinuierlich kaltgewalzter nichtrostender Stahl. Grenzabmaße und Formtoleranzen. Kaltbreitband und Blech
CommitteeISE/105
ISBN978 0 580 60754 7
PublisherBSI
FormatA4
DeliveryYes
Pages16
File Size789 KB
Price£130.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Collaborate, Innovate, Accelerate.


Worldwide Standards
We can source any standard from anywhere in the world


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version


Customers who bought this product also bought

  • BS EN ISO 9445-1:2010
    Continuously cold-rolled stainless steel. Tolerances on dimensions and form Narrow strip and cut lengths
  • BS EN 1706:2010
    Aluminium and aluminium alloys. Castings. Chemical composition and mechanical properties
  • BS EN ISO 8062-3:2007
    Geometrical product specifications (GPS). Dimensional and geometrical tolerances for moulded parts General dimensional and geometrical tolerances and machining allowances for castings
  • BS EN 1676:2010
    Aluminium and aluminium alloys. Alloyed ingots for remelting. Specifications