BS ISO 8710:2010 - Motorcycles. Brakes and brake systems. Tests and measurement methods – BSI British Standards

BS ISO 8710:2010

Motorcycles. Brakes and brake systems. Tests and measurement methods

Status : Confirmed, Current   Published : May 2010

Format
PDF

Format
HARDCOPY



BS ISO 8710:2010 Motorcycles. Brakes and brake systems. Tests and measurement methods

BS ISO 8710 specifies tests and measurement methods for service brake systems and, where applicable, associated parking brake systems of two-wheeled motorcycles, motorcycles with sidecar and tricycles which are intended for use on public roads, in order to establish uniform worldwide test procedures for braking systems.

BS ISO 8710 does not cover motorcycles which:

  • Have a maximum speed of less than 25 km/h
  • Are equipped for disabled riders.

BS ISO 8710 sets out the following types of tests:

  • Dyamic tests
  • Dy stop test (single brake control actuated)
  • Dy stop test (all service brake controls actuated)
  • Hgh speed test
  • Wt brake test
  • Hat fade test
  • Parking brake system test
  • Failure tests
  • Partial failure test (for split service brake systems)
  • Power-assisted brake system failure test.

The test methods (application, condition of the motorcycle, test procedure and parameters, measurement of performances) for all the tests defined in this International Standard are equivalent to the corresponding test methods prescribed by UNECE Global Technical Regulation No. 3.

Content of BS ISO 8710:

Foreword
1 Scope
2 Normative references
3 Terms and definitions
3.1 Vehicle categories
3.2 Brake system and components
3.3 Types of brake systems
3.4 Motorcycle loading
3.5 Test parameters
4 Test site conditions
4.1 Test surface
4.2 Wind speed
4.3 Ambient temperature
4.4 Test lane for dynamic tests
5 Motorcycle preparation
5.1 Tyres
5.2 Engine idle speed
5.3 Mass distribution
5.4 Instrumentation
5.5 Burnishing
6 Test requirements
6.1 Brakes
6.2 Brake temperature measurement
6.3 Application of control forces
6.4 Test sequence
6.5 Rider
6.6 Automatic transmission
6.7 Motorcycle position and wheel lock
6.8 Test speed tolerance
6.9 Measurement of dynamic performance
6.10 Test report
7 Test procedures
7.1 Dry stop test (single brake control actuated)
7.2 Dry stop test (all service brake controls actuated)
7.3 High speed test
7.4 Wet brake test
7.5 Heat fade test
7.6 Parking brake system test
7.7 Partial failure test (for split service brake systems)
7.8 Power-assisted brake system failure test
Annex A (normative) Specimen format for test result sheet
Bibliography

 




Standard NumberBS ISO 8710:2010
TitleMotorcycles. Brakes and brake systems. Tests and measurement methods
StatusConfirmed, Current
Publication Date31 May 2010
Confirm Date22 October 2015
Normative References(Required to achieve compliance to this standard)ISO 3779, ISO 7117
Informative References(Provided for Information)UNECE Global Technical Regulation No. 3, UNECE Special Resolution No. 1
International RelationshipsISO 8710:2010
Draft Superseded By07/30167889 DC
DescriptorsBraking systems, Two-wheeled motor vehicles, Sidecars, Braking tests, Braking system components, Dynamic testing, Motor cycles, Brakes, Three-wheeled motor vehicles, Braking
ICS43.140
Title in FrenchMotocyles. Freins et systèmes de freinage. Méthodes d'essai et de mesure
CommitteeAUE/14
ISBN978 0 580 59317 8
PublisherBSI
FormatA4
DeliveryYes
Pages40
File Size544 KB
Price£214.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


BSOL

The faster, easier way to work with standards


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version


Worldwide Standards
We can source any standard from anywhere in the world