BS EN 12588:2006 - Lead and lead alloys. Rolled lead sheet for building purposes – BSI British Standards

BS EN 12588:2006

Lead and lead alloys. Rolled lead sheet for building purposes

Status : Current   Published : January 2007

Format
PDF

Format
HARDCOPY



BS EN 12588 is a European standard that has been revised to include improved durability, safe handling and environmental management of the product. It specifies the designation; the requirements for chemical composition; surface condition, and dimensional tolerances for rolled lead sheet. Lead sheet covered by this standard is made by the roll deformation process and is intended for roofs, flashings, weatherings, claddings, pre-formed panels, damp-proof courses and similar building work.

A number of changes have been made, since the previous edition, and include the following:

  • Chemical composition
    Following extensive research carried out by TNO Institution Holland it was found that higher levels of tin content improved the products resistance to surface corrosion. Therefore the impurity maximum has been increased from 0,005 % to 0,05 %.
  • Safety
    The product covered in this standard, by definition is heavy. It has been necessary to provide clear guidance on manual lifting of the product.
  • Environment
    Studies into construction and demolition waste carried out by Enviros Aspinall have shown that the recycling rate of the product is above 90 %. Recommendations have been included within this standard on good management of surplus material during construction.
    In this European standard, the performance of the product has been defined as far as possible in terms of a number of type tests.

The performance of a building element made with these products depends not only on the properties of the product as it is required by this European standard, but also on the design and quality of the fabrication of the building element and on the design, construction and behaviour of the part of the building concerned in relation to the environment and conditions of use.

The lead sheet supplied shall be specified and used according to the National Code of Practice, depending on service conditions such as exposure to direct sunlight and the area of the piece of lead to be fixed.

No requirements for supporting construction, design of roof or cladding systems and methods of joining are included.

Contents Include:

  • Normative references
  • Terms and definitions
  • Designation
  • Material number
  • Product
  • Ordering information
  • Requirements
  • Chemical composition
  • Dimensions and tolerances
  • Surface condition
  • Test methods
  • Thickness
  • Apparatus Procedure
  • Chemical analysis
  • Sampling
  • Declaration of conformity
  • Marking, labelling and packaging
  • Colour codes for thickness
  • Transport, storage and handling
  • Safety
  • European numbering system for lead and lead alloys
  • Details of the system
  • Structure of number

BS EN 12588:2006 replaces BS EN 12588:1999, which has been withdrawn.




Standard NumberBS EN 12588:2006
TitleLead and lead alloys. Rolled lead sheet for building purposes
StatusCurrent
Publication Date31 January 2007
Normative References(Required to achieve compliance to this standard)No other standards are normatively referenced
Informative References(Provided for Information)No other standards are informatively referenced
ReplacesBS EN 12588:1999
International RelationshipsEN 12588:2006
Draft Superseded By06/30150574 DC
DescriptorsMarking, Colour codes, Lead alloys, Chemical composition, Materials handling, Length, Sheet materials, Storage, Cladding panels, Dimensional tolerances, Occupational safety, Lead, Thickness measurement, Flashing, Sheet roof coverings, Surfaces, Damp-proof courses, Designations, Width, Thickness, Construction materials, Sheet cladding, Ordering, Waste handling, Dimensions, Numerical designations
ICS77.150.60
91.100.01
Title in FrenchPlomb et alliages de plomb. Feuilles de plomb laminé pour le bâtiment
Title in GermanBlei und Bleilegierungen. Gewalzte Bleche aus Blei für das Bauwesen
CommitteeNFE/22
ISBN978 0 580 49960 9
PublisherBSI
FormatA4
DeliveryYes
Pages16
File Size249 KB
Price£130.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Worldwide Standards
We can source any standard from anywhere in the world


Develop a PAS

Develop a fast-track standardization document in 9-12 months


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version