BS EN 10327:2004 - Continuously hot-dip coated strip and sheet of low carbon steels for cold forming. Technical delivery conditions – BSI British Standards

BS EN 10327:2004

Continuously hot-dip coated strip and sheet of low carbon steels for cold forming. Technical delivery conditions

Status : Superseded, Withdrawn   Published : July 2004 Replaced By : BS EN 10346:2009

WITHDRAWN TITLE
*To ask about withdrawn titles contact the
BSI Customer Services
cservices@bsigroup.com, +44 345 086 9001


BS EN 10327:2004 specifies requirements for continuously hot-dip coated products made of low carbon steels for cold forming coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminium alloy (ZA), aluminium-zinc alloy (AZ) and aluminium-silicon alloy (AS) with thicknesses of 0.35 mm to 3.0 mm unless otherwise agreed. The thickness is the final thickness of the delivered product after coating.

This standard applies to strip of all widths and to sheets cut from it (greater than or equal to 600 mm width) and cut lengths (< 600 mm width).

This standard may also be applied to continuously hot-dip coated flat products in thicknesses > 3.0 mm.

The products covered by this standard are mainly used where cold formability and corrosion resistance are the most important factors.

This standard is not applicable to:

  • continuously hot-dip coated structural steel flat products
  • electrolytically zinc coated cold rolled steel flat products
  • continuously organic coated (coil coated) steel flat products
  • continuously hot-dip coated strip and sheet of steels with higher yield strength for cold forming.

BS EN 10327:2004 specifies requirements for continuously hot-dip coated products made of low carbon steels for cold forming coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminium alloy (ZA), aluminium-zinc alloy (AZ) and aluminium-silicon alloy (AS) with a thickness of 0.35 mm to 3.0 mm unless otherwise agreed.

This document applies to strips of all widths and to sheets cut from it (≥ 600 mm width) and cut lengths (< 600 mm width). If agreed at the time of enquiry and order, this document may also be applied to continuously hot-dip coated flat products in thicknesses > 3,0 mm. In this case the mechanical property, adhesion of coating and surface condition requirements shall also be agreed at the time of enquiry and order.

BS EN 10327:2004 is not applicable to continuously hot-dip coated structural steel flat products; electrolytically zinc coated cold rolled steel flat products; continuously organic coated (coil coated) steel flat products; or continuously hot-dip coated strip and sheet of steels with higher yield strength for cold forming.

Contents include:

  • Classification and designation
  • Requirements
  • Coating finish
  • Surface treatment (surface protection)
  • Stretcher strains
  • Adhesion of coating
  • Tolerances on dimensions and shape
  • Testing (units, numbers, sampling, methods and retests)
  • Storage and transportation
  • Chemical composition
  • Mechanical properties
  • Surface quality
  • Freedom from coil breaks
  • Coating mass
  • Surface condition
  • Suitability for further processing
  • Marking and packing
  • Disputes.



Standard NumberBS EN 10327:2004
TitleContinuously hot-dip coated strip and sheet of low carbon steels for cold forming. Technical delivery conditions
StatusSuperseded, Withdrawn
Publication Date14 July 2004
Withdrawn Date31 March 2009
Normative References(Required to achieve compliance to this standard)EN 10002-1, EN 10020:2000, EN 10021:1993, EN 10027-1, EN 10027-2, EN 10079:1992, EN 10143, EN 10204:1991, ISO 10113, ISO 10275, CR 10260
Informative References(Provided for Information)EN 10152, EN 10169-1, ENV 10169-2, EN 10169-3, EN 10292, EN 10326, EN ISO 14713, ISO 14713:1999
Replaced ByBS EN 10346:2009
ReplacesBS EN 10214:1995, BS EN 10215:1995, BS EN 10142:2000, BS EN 10154:2002
International RelationshipsEN 10327:2004
Draft Superseded By02/704946 DC
DescriptorsSteels, Unalloyed steels, Low-carbon steels, Sheet materials, Strips, Coatings, Metal coatings, Coated materials, Hot-dip coating, Cold-working, Zinc, Thickness
ICS77.140.50
Title in FrenchBandes et toles en acier doux revetues en continu par immersion a chaud pour formage a froid. Conditions techniques de livraison
Title in GermanKontinuierlich schmelztauchveredeltes Band und Blech aus weichen Staehlen zum Kaltumformen. Technische Lieferbedingungen
CommitteeISE/109
ISBN0 580 44085 0
PublisherBSI
FormatA4
DeliveryNo
Pages26
File Size460.6 KB
Price£182.00


WITHDRAWN TITLE
*To ask about withdrawn titles contact the
BSI Customer Services
cservices@bsigroup.com, +44 345 086 9001
 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Develop a PAS

Develop a fast-track standardization document in 9-12 months


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version


BSOL

The faster, easier way to work with standards


Customers who bought this product also bought

  • BS EN 10326:2004
    Continuously hot-dip coated strip and sheet of structural steels. Technical delivery conditions
  • BS EN 10143:2006
    Continuously hot-dip coated steel sheet and strip. Tolerances on dimensions and shape
  • BS EN 10130:2006
    Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions
  • BS EN 10131:2006
    Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming. Tolerances on dimensions and shape