BS 6002-4.1:1994, ISO 8423:1991 - Sampling procedures for inspection by variables. Specification for sequential sampling plans for percent nonconforming. Known standard deviation – BSI British Standards

BS 6002-4.1:1994, ISO 8423:1991

Sampling procedures for inspection by variables. Specification for sequential sampling plans for percent nonconforming. Known standard deviation

Status : Superseded, Withdrawn   Published : March 1994 Replaced By : BS 6002-4:2006, ISO 3951-5:2006, BS ISO 8423:2008

WITHDRAWN TITLE
*To ask about withdrawn titles contact the
BSI Customer Services
cservices@bsigroup.com, +44 345 086 9001


This International Standard specifies sequential sampling plans and procedures for inspection by variables of discrete items. It is complementary to ISO 8422. The plans in the main body of the standard are indexed in terms of the producer’s risk point and the consumer’s risk point.

Annex A specifies sequential sampling plans and procedures indexed in terms of the acceptable quality level (AQL) to supplement the system of sampling plans in ISO 3951.

The purpose of this International Standard is to provide procedures based on a sequential assessment of inspection results, that may be used to induce the supplier through the economic and psychological pressure of non-acceptance of lots of inferior quality to supply lots of a quality having a high probability of acceptance. At the same time the consumer is protected by a prescribed upper limit to the probability of accepting lots of poor quality. 

The sampling plans in this International Standard are primarily designed for use when all of the following conditions are satisfied:

  • where the inspection procedure is to be applied to a continuing series of lots of discrete items all supplied by one producer using one production process. If there are different producers, this International Standard shall be applied to each one separately;
  • where only a single quality characteristic x of these items is taken into consideration, which must be measurable on a continuous scale. If several such characteristics are of importance, this International Standard does not apply;
  • where production is stable (under statistical control) and the quality characteristic x has a known standard deviation and is distributed according to a normal distribution or a close approximation to the normal distribution;
  • where a contract or standard defines an upper specification limit U, a lower specification limit L, or both; an item is qualified as nonconforming when its measured quality characteristic x satisfies one of the following inequalities:

x > U ... (1.1) x < L ... (1.2)
either
x > U
or
x < L ... (1.3)




Standard NumberBS 6002-4.1:1994, ISO 8423:1991
TitleSampling procedures for inspection by variables. Specification for sequential sampling plans for percent nonconforming. Known standard deviation
StatusSuperseded, Withdrawn
Publication Date15 March 1994
Withdrawn Date30 September 2008
Normative References(Required to achieve compliance to this standard)No other standards are normatively referenced
Informative References(Provided for Information)No other standards are informatively referenced
Replaced ByBS 6002-4:2006, ISO 3951-5:2006, BS ISO 8423:2008
International RelationshipsISO 8423:1991
DescriptorsInspection by variables, Inspection, Sequential sampling, Statistical quality control, Quality control, Control charts, Mathematical calculations, Sampling tables, Acceptance inspection, Sampling methods, Assessed quality, Normal distribution, Standard deviation, Statistical distribution, Measurement characteristics
ICS03.120.30
Title in FrenchPlans d'echantillonnage progressif pour le controle par mesures des pourcentages de non conformes (ecart-type connu)
Title in GermanSequentielle Stichprobenpruefung auf den Anteil fehlerhafter Einheiten in Prozent anhand quantitativer Merkmale (bei bekannter Standardabweichung)
CommitteeSS/5
ISBN0 580 22953 X
PublisherBSI
FormatA4
DeliveryNo
Pages42
File Size1.093 MB
Price£214.00


WITHDRAWN TITLE
*To ask about withdrawn titles contact the
BSI Customer Services
cservices@bsigroup.com, +44 345 086 9001
 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


BSOL

The faster, easier way to work with standards


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version


Worldwide Standards
We can source any standard from anywhere in the world