BS EN 9103:2014 - Aerospace series. Quality management systems. Variation management of key characteristics

BS EN 9103:2014

Aerospace series. Quality management systems. Variation management of key characteristics

Status : Current   Published : December 2014

Format
PDF

Format
HARDCOPY



This standard is primarily intended to apply to new parts and products, but can also be applied to parts currently in production. The standard shall be applicable to all production processes that influence the variation of KCs, as well as maintenance processes in which KCs are identified. It applies to assemblies and all levels of parts within an assembly, down to the basic materials including castings and forgings, and to organizations that are responsible for producing the design characteristics of the product.

It does not apply to lab-scale, pilot, or pre-production processes. However, particular management of some KCs might be required using other methods than those described in the standard, during these phases of a programme, when required by the customer or deemed appropriate by the organization (e.g., Engineering department requirement).

The variation control process begins with product definition, typically an engineering drawing or specification which identifies KCs, and leads to a variation management program for those KCs. This process may also be used for producer-identified KCs.

Producers and their subcontractors shall be responsible for flow down of the requirements of the applicable revision of this standard to subcontractors, who produce design characteristics, and for ensuring that KCs conform to customer requirements.

1.1 Purpose

This standard is designed to drive the improvement of manufacturing and maintenance processes through adequate planning and effective management of KC variation. The KC focus is intended to improve confidence for part features whose variation has a significant influence on to end-product form, fit, performance, service life, and producibility.

NOTE

Control of a product or process KC per this standard does not constitute, nor imply, acceptance of the resulting product. If variation management, under this standard, is to be part of an acceptance decision, the requirements must be specified in the applicable product acceptance plan or contract.

1.2 Convention

The following conventions are used in this standard:

  • The words "shall", "will", or "must" indicate mandatory requirements.

  • The word "should" indicates a requirement with some flexibility allowed in compliance methodology.

  • Producers choosing other methods to satisfy a "should" shall be able to show that their approach meets the intent of the requirements of this standard.

  • Words "typical", "example", "for reference", "may", or "e.g." indicate suggestions given for guidance only.

  • "NOTES" are used for additional clarification.

  • Words or phrases with specific meaning pertaining to this document are defined in Clause 3, Terms and Definitions.




Standard NumberBS EN 9103:2014
TitleAerospace series. Quality management systems. Variation management of key characteristics
StatusCurrent
Publication Date31 December 2014
Normative References(Required to achieve compliance to this standard)EN 9100, EN 9102, EN 9110, ISO 9000:2005, ISO 9001:2008, ISO 9004:2009
Informative References(Provided for Information)No other standards are informatively referenced
ReplacesBS EN 9103:2005
International RelationshipsEN 9103:2014
Amended ByCorrigendum, January 2016.
Draft Superseded By11/30247885 DC
DescriptorsAir transport engineering, Aircraft components, Quality management, Quality assurance systems, Quality assurance, Production planning, Planning, Management, Management operations, Technical documents
ICS03.100.70
03.120.10
49.020
Title in FrenchSérie aérospatiale. Systèmes de management de la qualité. Management de la variation des caractéristiques clefs
Title in GermanLuft- und Raumfahrt. Qualitätsmanagementsystems. Management der Veränderung der Haupteigenshaften
CommitteeACE/1
ISBN978 0 580 92501 6
PublisherBSI
FormatA4
DeliveryYes
Pages22
File Size1.112 MB
Price£130.00


 Your basket
Your basket is empty

Multi-user access to over 3,500 medical device standards, regulations, expert commentaries and other documents


Develop a PAS

Develop a fast-track standardization document in 9-12 months


BSOL

The faster, easier way to work with standards


Tracked Changes

Understand the changes made to a standard with our new Tracked Changes version


Customers who bought this product also bought

  • BS EN 9102:2015
    Aerospace series. Quality systems. First article inspection requirements