BS EN ISO 13849-1:2006 - Safety of machinery. Safety-related parts of control systems. General principles for design – BSI British Standards

Find Similar Items

This product falls into the following categories.

You may find similar items within these categories by selecting from the choices below:

BS EN ISO 13849-1:2006

Safety of machinery. Safety-related parts of control systems. General principles for design

Status : Revised, Withdrawn   Published : May 2007 Replaced By : BS EN ISO 13849-1:2008

WITHDRAWN TITLE
*To ask about withdrawn titles contact the BSI Knowledge Centre knowledgecentre@bsigroup.com,
+44 20 8996 7004


BS EN ISO 13849-1:2006 provides safety requirements and guidance on the principles for the design and integration of safety-related parts of control systems (SRP/CS), including the design of software. For these parts of SRP/CS, it specifies characteristics that include the performance level required for carrying out safety functions. It applies to SRP/CS, regardless of the type of technology and energy used (electrical, hydraulic, pneumatic, mechanical, etc.), for all kinds of machinery.

It applies to SRP/CS, regardless of the type of technology and energy used (electrical, hydraulic, pneumatic, mechanical, etc.), for all kinds of machinery. (It is recommended that EN ISO 13849-1:2006 is used primarily for the design of low complexity SRP/CS).

The performance levels and categories can be applied to safety-related parts of control systems, such as

  • Protective devices (e.g. two-hand control devices, interlocking devices), electro-sensitive protective devices (e.g. photoelectric barriers), pressure sensitive devices
  • Control units (e.g. a logic unit for control functions, data processing, monitoring, etc.)
  • Power control elements (e.g. relays, valves, etc), as well as to control systems carrying out safety functions at all kinds of machinery — from simple (e.g. small kitchen machines, or automatic doors and gates) to manufacturing installations (e.g. packaging machines, printing machines, presses).

Part 1 of this international standard is intended to provide a clear basis upon which the design and performance of any application of the SRP/CS (and the machine) can be assessed, for example, by a third party, in-house or by an independent test house.

It does not specify the safety functions or performance levels that are to be used in a particular case.

Part 1 of BS EN ISO 13849 provides specific requirements for SRP/CS using programmable electronic system(s). It does not give specific requirements for the design of products which are parts of SRP/CS. Nevertheless, the principles given, such as categories or performance levels, can be used.

This part of ISO 13849 is intended to give guidance to those involved in the design and assessment of control systems, and to Technical Committees preparing Type-B2 or Type-C standards which are presumed to comply with The Machinery Directive. It does not give specific guidance for compliance with other EC directives.

As part of the overall risk reduction strategy at a machine, a designer will often choose to achieve some measure of risk reduction through the application of safeguards employing one or more safety functions.

Parts of machinery control systems that are assigned to provide safety functions are called safety-related parts of control systems (SRP/CS) and these can consist of hardware and software and can either be separate from the machine control system or an integral part of it. In addition to providing safety functions, SRP/CS can also provide operational functions (e.g. two-handed controls as a means of process initiation).

In order to assist the designer and help facilitate the assessment of achieved PL, this document employs a methodology based on the categorization of structures according to specific design criteria and specified behaviours under fault conditions.

Download the Introduction pages [pdf 54KB]

Contents include:

  • Scope
  • Normative references
  • Terms, definitions, symbols and abbreviated terms
  • Design considerations
  • Safety objectives in design
  • Strategy for risk reduction
  • Contribution to the risk reduction by the control system
  • Determination of required performance level (PLr)
  • Design of SRP/CS
  • Evaluation of the achieved performance level PL and relationship with SIL
  • Performance level PL
  • Mean time to dangerous failure of each channel (MTTFd)
  • Diagnostic coverage (DC)
  • Simplified procedure for estimating PL
  • Software safety requirements
  • Safety-related embedded software (SRESW)
  • Safety-related application software (SRASW)
  • Software-based parameterization
  • Verification that achieved PL meets PLr
  • Ergonomic aspects of design
  • Safety functions
  • Safety-related stop function
  • Manual reset function
  • Start/restart function
  • Local control function
  • Muting function
  • Response time
  • Safety-related parameters
  • Fluctuations, loss and restoration of power sources
  • Categories and their relation to MTTFd of each channel, DCavg and CCF
  • Specifications of categories
  • Designated architectures
  • Combination of SRP/CS to achieve overall PL
  • Fault consideration, fault exclusion
  • Validation
  • Maintenance
  • Technical documentation
  • Information for use
  • Determination of required performance level (PLr)
  • Block method and safety-related block diagram
  • Calculating or evaluating MTTFd values for single components
  • Simplified method for estimating MTTFd for each channel
  • Estimates for diagnostic coverage (DC) for functions and modules
  • Estimates for common cause failure (CCF)
  • Systematic failure
  • Example of combination of several safety-related parts of the control system
  • Software
  • Relationship between this European Standard and the Essential
  • Requirements of EU Directive 98/37/EC, amended by Directive 98/79/EC
  • Bibliography

 




Standard NumberBS EN ISO 13849-1:2006
TitleSafety of machinery. Safety-related parts of control systems. General principles for design
StatusRevised, Withdrawn
Publication Date31 May 2007
Withdrawn Date30 June 2009
Cross ReferencesISO 12100-1:2003, ISO 12100-2:2003, ISO 13849-2:2003, ISO 14121, IEC 60050-191:1990, IEC 60050-191:1990/AMD 1:1999, IEC 60050-191:1990/AMD 2:2002, IEC 61508-3:1998, IEC 61508-3:1998/Corrigendum 1:1999, IEC 61508-4:1998, IEC 61508-4:1998/Corrigendum 1:1999, 98/37/EC, 98/79/EC, IEC 61000-4-4, IEC 61496-1, IEC 61496-2, IEC 61496-3, IEC 61508-1:1998, IEC 61508-2:2000, IEC 61508-5:1998, IEC 61508-6:2000, IEC 61508-7:2000, IEC 62061, ISO/FDIS 13850, ISO 13851, ISO 13856-1, ISO 13856-2, ISO 11428, ISO 9001, ISO 9355-1, ISO 9355-2, ISO 9355-3, ISO 11429, ISO 7731, ISO 4413, ISO 4414, ISO 13855:2000, ISO 14118, ISO 19973, IEC 60204-1:2005, IEC 60447, IEC 60529, IEC 60812, IEC 60947, IEC 61000-6-2, IEC 61800-3, IEC 61810, IEC 61300, IEC 61310, IEC 61131-3, EN 457, EN 614-1, EN 982, EN 983, EN 1005-3, EN 1088, EN 50205, SN 29500, IEC/TR 62380
Replaced ByBS EN ISO 13849-1:2008
ReplacesBS EN 954-1:1997
International RelationshipsEN ISO 13849-1:2006,ISO 13849-1:2006
Draft Superseded By04/30086349 DC
DescriptorsEquipment safety, Occupational safety, Control systems, Control equipment, Safety devices, Design, Safety measures, Classification systems, Grades (quality), Reliability, Risk assessment, Computer software, Computerized control, Automatic control systems, Electronic equipment and components, Defects, Instructions for use
ICS13.110
29.020
Title in FrenchSécurité des machines. Parties des systèmes de commande relatives à la sécurité. Principes généraux de conception
Title in GermanSicherheit von Maschinen. Sicherheitsbezogene Teile von Steuerungen. Allgemeine Gestaltungsleitsätze
CommitteeMCE/3
ISBN978 0 580 50882 0
PublisherBSI
FormatA4
DeliveryNo
Pages100
File Size2.188 MB
Price£244.00


WITHDRAWN TITLE
*To ask about withdrawn titles contact the BSI Knowledge Centre knowledgecentre@bsigroup.com,
+44 20 8996 7004
 Your basket
Your basket is empty

Take the smart route to manage medical device compliance


Collaborate, Innovate, Accelerate.


BSOL

The faster, easier way to work with standards


Worldwide Standards
We can source any standard from anywhere in the world


Customers who bought this product also bought