BS EN 10326:2004 - Continuously hot-dip coated strip and sheet of structural steels. Technical delivery conditions – BSI British Standards

Find Similar Items

This product falls into the following categories.

You may find similar items within these categories by selecting from the choices below:

BS EN 10326:2004

Continuously hot-dip coated strip and sheet of structural steels. Technical delivery conditions

Status : Superseded, Withdrawn   Published : July 2004 Replaced By : BS EN 10346:2009

WITHDRAWN TITLE
*To ask about withdrawn titles contact the BSI Knowledge Centre knowledgecentre@bsigroup.com,
+44 20 8996 7004


BS EN 10326:2004 specifies requirements for continuously hot-dip coated products made of structural steels coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminium alloy (ZA), aluminium-zinc alloy (AZ) and aluminium-silicon alloy (AS) with thicknesses from 0.35 mm up to 3.0 mm unless otherwise agreed. The thickness is the final thickness of the delivered product after coating.

This standard applies to strip of all widths and to sheets cut from it (greater than or equal to 600 mm width) and cut lengths (< 600 mm width).

This standard may also be applied to continuously hot-dip coated flat products in thicknesses > 3.0 mm.

The products covered by this standard are mainly used where minimum yield strength and corrosion resistance are the most important factors.

This standard is not applicable to:

  • continuously hot-dip coated flat products of low-carbon steel strip and sheet for cold forming
  • electrolytic galvanized cold rolled steel flat products
  • continuously organic coated (coil coated) flat steel products
  • continuously hot-dip coated strip and sheet of steels with higher yield strength for cold forming.

BS EN 10326:2004 specifies requirements for continuously hot-dip coated products made of structural steels coated with zinc (Z), zinc-iron alloy (ZF), zinc-aluminium alloy (ZA), aluminium-zinc alloy (AZ) and aluminium-silicon alloy (AS) with a thickness of 0.35 mm up to 3.0 mm unless otherwise agreed. The thickness is the final thickness of the delivered product after coating.

This standard applies to strips of all widths and to sheets cut from it (≥ 600 mm width) and cut lengths (< 600 mm width). If agreed at the time of enquiry and order, this document may also be applied to continuously hot-dip coated flat products in thicknesses > 3.0 mm. In this case the mechanical property, adhesion of coating and surface condition requirements shall also be agreed at the time of enquiry and order.

The products covered by BS EN 10326 are mainly used where minimum yield strength and corrosion resistance are the most important factors.

This document is not applicable to continuously hot-dip coated flat products of low carbon steel strips and sheets for cold forming; electrolytic galvanized cold rolled steel flat products; continuously organic coated (coil coated) flat steel products; continuously hot-dip coated strips and sheets of steels with higher yield strength for cold forming.

Contents include:

  • Classification and designation
  • Requirements
  • Coating finish
  • Surface treatment (surface protection)
  • Stretcher strains
  • Adhesion of coating
  • Tolerances on dimensions and shape
  • Testing (units, numbers, sampling, methods and retests)
  • Storage and transportation
  • Chemical composition
  • Mechanical properties
  • Surface quality
  • Freedom from coil breaks
  • Coating mass
  • Surface condition
  • Suitability for further processing
  • Marking and packing
  • Disputes.



Standard NumberBS EN 10326:2004
TitleContinuously hot-dip coated strip and sheet of structural steels. Technical delivery conditions
StatusSuperseded, Withdrawn
Publication Date14 July 2004
Withdrawn Date31 March 2009
Cross ReferencesEN 10002-1, EN 10020:2000, EN 10021:1993, EN 10027-1, EN 10027-2, EN 10079:1992, EN 10143, EN 10204:1991, CR 10260, EN 10152, EN 10169-1, ENV 10169-2, EN 10169-3, EN 10292, EN 10327, EN ISO 14713, ISO 14713:1999
Replaced ByBS EN 10346:2009
ReplacesBS EN 10214:1995, BS EN 10215:1995, BS EN 10147:2000, BS EN 10154:2002
International RelationshipsEN 10326:2004
Draft Superseded By02/704945 DC
DescriptorsStructural steels, Steels, Strips, Sheet materials, Zinc, Coatings, Metal coatings, Dip coating, Hot-dip coating, Hot-dip galvanizing, Delivery, Flat (shape), Thickness, Width, Mass, Finishes, Surfaces, Yield strength, Corrosion resistance
ICS77.140.10
77.140.50
Title in FrenchBandes et toles en aciers de construction doux revetues en continu par immersion a chaud. Conditions techniques de livraison
Title in GermanKontinuierlich schmelztauchveredeltes Band und Blech aus Baustaehlen. Technische Lieferbedingungen
CommitteeISE/109
ISBN0 580 44084 2
PublisherBSI
FormatA4
DeliveryNo
Pages24
File Size431.7 KB
Price£164.00


WITHDRAWN TITLE
*To ask about withdrawn titles contact the BSI Knowledge Centre knowledgecentre@bsigroup.com,
+44 20 8996 7004
 Your basket
Your basket is empty

Take the smart route to manage medical device compliance


Collaborate, Innovate, Accelerate.


BSOL

The faster, easier way to work with standards


BSI Essentials

Get ISO 9001 and ISO 9000 with 15% discount.


Customers who bought this product also bought

  • BS EN 10327:2004
    Continuously hot-dip coated strip and sheet of low carbon steels for cold forming. Technical delivery conditions
  • BS EN 10143:2006
    Continuously hot-dip coated steel sheet and strip. Tolerances on dimensions and shape
  • BS EN 10130:2006
    Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions
  • BS EN 10131:2006
    Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming. Tolerances on dimensions and shape